[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Can't boot 5.2-RC2 on Acer TravelMate 800LCi



Trying to boot from the CD-ROM will hang the system reliably,
with or without ACPI.

I hope that someone may have an idea about what's wrong here,
so I enclose the following output.

Thank you,
Toni

...
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <ACER   Cardinal> on motherboard
pci_open(1):    mode 1 addr port (0x0cf8) is 0x80010014
pci_open(1a):   mode1res=0x80000000 (0x80000000)
pci_cfgcheck:   device 0 [class=060000] [hdr=00] is there (id=33408086)
pcibios: BIOS version 2.10
Using $PIR table, 10 entries at 0xc00fdcb0
PCI-Only Interrupts: none
Location  Bus Device Pin  Link  IRQs
embedded    0   30    A   0x60  3 4 5 6 7 9 10 11 12
embedded    0   30    B   0x61  3 4 5 6 7 9 10 11 12
embedded    0   30    C   0x62  3 4 5 6 7 9 10 11 12
embedded    0   30    D   0x63  3 4 5 6 7 9 10 11 12
embedded    2    6    A   0x61  3 4 5 6 7 9 10 11 12
embedded    2    4    A   0x68  3 4 5 6 7 9 10 11 12
embedded    2    4    B   0x69  3 4 5 6 7 9 10 11 12
embedded    2    7    A   0x62  10
embedded    2    2    A   0x63  3 4 5 6 7 9 10 11 12
embedded    0    0    A   0x60  3 4 5 6 7 9 10 11 12
embedded    0    0    B   0x61  3 4 5 6 7 9 10 11 12
embedded    0    0    C   0x62  3 4 5 6 7 9 10 11 12
embedded    0    0    D   0x63  3 4 5 6 7 9 10 11 12
embedded    0   31    A   0x62  3 4 5 6 7 9 10 11 12
embedded    0   31    B   0x61  3 4 5 6 7 9 10 11 12
embedded    0   29    A   0x60  3 4 5 6 7 9 10 11 12
embedded    0   29    B   0x63  3 4 5 6 7 9 10 11 12
embedded    0   29    C   0x62  3 4 5 6 7 9 10 11 12
embedded    0   29    D   0x6b  3 4 5 6 7 9 10 11 12
embedded    0    1    A   0x60  3 4 5 6 7 9 10 11 12
embedded    0    1    B   0x61  3 4 5 6 7 9 10 11 12
slot 1      1    0    A   0x60  3 4 5 6 7 9 10 11 12
AcpiOsDerivePciId: bus 0 dev 31 func 0
AcpiOsDerivePciId: bus 0 dev 31 func 1
acpi0: Power Button (fixed)
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
AcpiOsDerivePciId: bus 0 dev 0 func 0
AcpiOsDerivePciId: bus 0 dev 31 func 0
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
---- initial configuration ------------------------
\_SB_.PCI0.LPC0.LNKA irq  10: [ 10] low,level,sharable 0.0.0
\_SB_.PCI0.LPC0.LNKB irq  10: [ 10] low,level,sharable 0.0.1
\_SB_.PCI0.LPC0.LNKC irq  10: [ 10] low,level,sharable 0.0.2
\_SB_.PCI0.LPC0.LNKD irq   5: [  5] low,level,sharable 0.0.3
\_SB_.PCI0.LPC0.LNKA irq  10: [ 10] low,level,sharable 0.1.0
\_SB_.PCI0.LPC0.LNKA irq  10: [ 10] low,level,sharable 0.29.0
\_SB_.PCI0.LPC0.LNKD irq   5: [  5] low,level,sharable 0.29.1
\_SB_.PCI0.LPC0.LNKC irq  10: [ 10] low,level,sharable 0.29.2
\_SB_.PCI0.LPC0.LNKH irq  10: [ 10] low,level,sharable 0.29.3
\_SB_.PCI0.LPC0.LNKA irq  10: [ 10] low,level,sharable 0.30.0
\_SB_.PCI0.LPC0.LNKB irq  10: [ 10] low,level,sharable 0.30.1
\_SB_.PCI0.LPC0.LNKC irq  10: [ 10] low,level,sharable 0.30.2
\_SB_.PCI0.LPC0.LNKD irq   5: [  5] low,level,sharable 0.30.3
\_SB_.PCI0.LPC0.LNKC irq  10: [ 10] low,level,sharable 0.31.0
\_SB_.PCI0.LPC0.LNKB irq  10: [ 10] low,level,sharable 0.31.1
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\_SB_.PCI0.LPC0.LNKA irq  10: [ 10] low,level,sharable 0.0.0
\_SB_.PCI0.LPC0.LNKB irq  10: [ 10] low,level,sharable 0.0.1
\_SB_.PCI0.LPC0.LNKC irq  10: [ 10] low,level,sharable 0.0.2
\_SB_.PCI0.LPC0.LNKD irq   5: [  5] low,level,sharable 0.0.3
\_SB_.PCI0.LPC0.LNKA irq  10: [ 10] low,level,sharable 0.1.0
\_SB_.PCI0.LPC0.LNKA irq  10: [ 10] low,level,sharable 0.29.0
\_SB_.PCI0.LPC0.LNKD irq   5: [  5] low,level,sharable 0.29.1
\_SB_.PCI0.LPC0.LNKC irq  10: [ 10] low,level,sharable 0.29.2
\_SB_.PCI0.LPC0.LNKH irq  10: [ 10] low,level,sharable 0.29.3
\_SB_.PCI0.LPC0.LNKA irq  10: [ 10] low,level,sharable 0.30.0
\_SB_.PCI0.LPC0.LNKB irq  10: [ 10] low,level,sharable 0.30.1
\_SB_.PCI0.LPC0.LNKC irq  10: [ 10] low,level,sharable 0.30.2
\_SB_.PCI0.LPC0.LNKD irq   5: [  5] low,level,sharable 0.30.3
\_SB_.PCI0.LPC0.LNKC irq  10: [ 10] low,level,sharable 0.31.0
\_SB_.PCI0.LPC0.LNKB irq  10: [ 10] low,level,sharable 0.31.1
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
        map[10]: type 3, range 32, base e0000000, size 28, enabled
found-> vendor=0x8086, dev=0x3340, revid=0x03
        bus=0, slot=0, func=0
        class=06-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0106, statreg=0x2090, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x3341, revid=0x03
        bus=0, slot=1, func=0
        class=06-04-00, hdrtype=0x01, mfdev=0
        cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords)
        lattimer=0x60 (2880 ns), mingnt=0x0c (3000 ns), maxlat=0x00 (0 ns)
        map[20]: type 4, range 32, base 00001800, size  5, enabled
pcib0: matched entry for 0.29.INTA (source \_SB_.PCI0.LPC0.LNKA)
pcib0: slot 29 INTA is routed to irq 10
found-> vendor=0x8086, dev=0x24c2, revid=0x03
        bus=0, slot=29, func=0
        class=0c-03-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
        map[20]: type 4, range 32, base 00001820, size  5, enabled
pcib0: matched entry for 0.29.INTB (source \_SB_.PCI0.LPC0.LNKD)
pcib0: slot 29 INTB is routed to irq 5
found-> vendor=0x8086, dev=0x24c4, revid=0x03
        bus=0, slot=29, func=1
        class=0c-03-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=5
        map[20]: type 4, range 32, base 00001840, size  5, enabled
pcib0: matched entry for 0.29.INTC (source \_SB_.PCI0.LPC0.LNKC)
pcib0: slot 29 INTC is routed to irq 10
found-> vendor=0x8086, dev=0x24c7, revid=0x03
        bus=0, slot=29, func=2
        class=0c-03-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=c, irq=10
        map[10]: type 1, range 32, base d0000000, size 10, enabled
pcib0: matched entry for 0.29.INTD (source \_SB_.PCI0.LPC0.LNKH)
pcib0: slot 29 INTD is routed to irq 10
found-> vendor=0x8086, dev=0x24cd, revid=0x03
        bus=0, slot=29, func=7
        class=0c-03-20, hdrtype=0x00, mfdev=0
        cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=d, irq=10
        powerspec 2  supports D0 D3  current D0
found-> vendor=0x8086, dev=0x2448, revid=0x83
        bus=0, slot=30, func=0
        class=06-04-00, hdrtype=0x01, mfdev=0
        cmdreg=0x0107, statreg=0x8080, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x24cc, revid=0x03
        bus=0, slot=31, func=0
        class=06-01-00, hdrtype=0x00, mfdev=1
        cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        map[10]: type 4, range 32, base 00000000, size  3, enabled
        map[14]: type 4, range 32, base 00000000, size  2, enabled
        map[18]: type 4, range 32, base 00000000, size  3, enabled
        map[1c]: type 4, range 32, base 00000000, size  2, enabled
        map[20]: type 4, range 32, base 00001860, size  4, enabled
found-> vendor=0x8086, dev=0x24ca, revid=0x03
        bus=0, slot=31, func=1
        class=01-01-8a, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=255
        map[20]: type 4, range 32, base 00001880, size  5, enabled
pcib0: matched entry for 0.31.INTB (source \_SB_.PCI0.LPC0.LNKB)
pcib0: slot 31 INTB is routed to irq 10
found-> vendor=0x8086, dev=0x24c3, revid=0x03
        bus=0, slot=31, func=3
        class=0c-05-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=10
        map[10]: type 4, range 32, base 00001c00, size  8, enabled
        map[14]: type 4, range 32, base 000018c0, size  6, enabled
        map[18]: type 1, range 32, base d0000c00, size  9, enabled
        map[1c]: type 1, range 32, base d0000800, size  8, enabled
pcib0: matched entry for 0.31.INTB (source \_SB_.PCI0.LPC0.LNKB)
pcib0: slot 31 INTB is routed to irq 10
found-> vendor=0x8086, dev=0x24c5, revid=0x03
        bus=0, slot=31, func=5
        class=04-01-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=10
        powerspec 2  supports D0 D3  current D0
        map[10]: type 4, range 32, base 00002400, size  8, enabled
        map[14]: type 4, range 32, base 00002000, size  7, enabled
pcib0: matched entry for 0.31.INTB (source \_SB_.PCI0.LPC0.LNKB)
pcib0: slot 31 INTB is routed to irq 10
found-> vendor=0x8086, dev=0x24c6, revid=0x03
        bus=0, slot=31, func=6
        class=07-03-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=10
        powerspec 2  supports D0 D3  current D0
agp0: <Intel 82855 host to AGP bridge> mem 0xe0000000-0xefffffff at device 0.0 on pci0
agp0: allocating GATT for aperture of size 256M
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0x3000-0x3fff
pcib1:   memory decode     0xd0100000-0xd01fffff
pcib1:   prefetched decode 0xd8000000-0xdfffffff
---- initial configuration ------------------------
\_SB_.PCI0.LPC0.LNKA irq  10: [ 10] low,level,sharable 1.0.0
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\_SB_.PCI0.LPC0.LNKA irq  10: [ 10] low,level,sharable 1.0.0
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
        map[10]: type 3, range 32, base d8000000, size 27, enabled
        map[14]: type 4, range 32, base 00003000, size  8, enabled
        map[18]: type 1, range 32, base d0103000, size 16, enabled
pcib1: matched entry for 1.0.INTA (source \_SB_.PCI0.LPC0.LNKA)
pcib1: slot 0 INTA is routed to irq 10
found-> vendor=0x1002, dev=0x4c66, revid=0x01
        bus=1, slot=0, func=0
        class=03-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0387, statreg=0x02b0, cachelnsz=8 (dwords)
        lattimer=0x42 (1980 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
        powerspec 2  supports D0 D1 D2 D3  current D0
pci1: <display, VGA> at device 0.0 (no driver attached)
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0x1800-0x181f irq 10 at device 29.0 on pci0
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0x1820-0x183f irq 5 at device 29.1 on pci0
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ums0: Cherry Mikroschalter product 0x000c rev 1.10/8.00, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0x1840-0x185f irq 10 at device 29.2 on pci0
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pci0: <serial bus, USB> at device 29.7 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib2:   secondary bus     2
pcib1:   subordinate bus   2
pcib1:   I/O decode        0x4000-0x4fff
pcib1:   memory decode     0xd0200000-0xd05fffff
pcib1:   prefetched decode 0xfff00000-0xfffff
---- initial configuration ------------------------
\_SB_.PCI0.LPC0.LNKD irq   5: [  5] low,level,sharable 2.2.0
\_SB_.PCI0.LPC0.LNKE irq  10: [  3  4  5  7  9 11 12] low,level,sharable 2.4.0
\_SB_.PCI0.LPC0.LNKF irq   0: [  3  4  5  7  9 11 12] low,level,sharable 2.4.1
\_SB_.PCI0.LPC0.LNKB irq  10: [ 10] low,level,sharable 2.6.0
\_SB_.PCI0.LPC0.LNKC irq  10: [ 10] low,level,sharable 2.7.0
---- before setting priority for links ------------
\_SB_.PCI0.LPC0.LNKF:
        interrupts:          3     4     5     7     9    11    12
        penalty:          1110  1110   510  1110   110   110  1110
        references:     1
        priority:       0
---- before fixup boot-disabled links -------------
\_SB_.PCI0.LPC0.LNKF:
        interrupts:          3     4     5     7     9    11    12
        penalty:          1110  1110   510  1110   110   110  1110
        references:     1
        priority:       738
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\_SB_.PCI0.LPC0.LNKD irq   5: [  5] low,level,sharable 2.2.0
\_SB_.PCI0.LPC0.LNKE irq  10: [  3  4  5  7  9 11 12] low,level,sharable 2.4.0
\_SB_.PCI0.LPC0.LNKF irq  11: [  3  4  5  7  9 11 12] low,level,sharable 2.4.1
\_SB_.PCI0.LPC0.LNKB irq  10: [ 10] low,level,sharable 2.6.0
\_SB_.PCI0.LPC0.LNKC irq  10: [ 10] low,level,sharable 2.7.0
pci2: <ACPI PCI bus> on pcib2
pci2: physical bus=2
        map[10]: type 1, range 32, base d0204000, size 13, enabled
pcib2: matched entry for 2.2.INTA (source \_SB_.PCI0.LPC0.LNKD)
pcib2: slot 2 INTA is routed to irq 5
found-> vendor=0x14e4, dev=0x4401, revid=0x01
        bus=2, slot=2, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0106, statreg=0x0010, cachelnsz=0 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=5
        powerspec 2  supports D0 D1 D2 D3  current D0
        map[10]: type 1, range 32, base d0206000, size 12, enabled
pcib2: matched entry for 2.4.INTA (source \_SB_.PCI0.LPC0.LNKE)
pcib2: slot 4 INTA is routed to irq 5
found-> vendor=0x8086, dev=0x1043, revid=0x04
        bus=2, slot=4, func=0
        class=02-80-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0116, statreg=0x0290, cachelnsz=8 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x02 (500 ns), maxlat=0x22 (8500 ns)
	intpin=a, irq=10
        powerspec 2  supports D0 D3  current D0
        map[10]: type 1, range 32, base d0207000, size 12, enabled
found-> vendor=0x1217, dev=0x7114, revid=0x20
        bus=2, slot=6, func=0
        class=06-07-00, hdrtype=0x02, mfdev=1
        cmdreg=0x0187, statreg=0x0410, cachelnsz=0 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0xc0 (48000 ns), maxlat=0x03 (750 ns)
	intpin=a, irq=255
        powerspec 2  supports D0 D1 D2 D3  current D0
found-> vendor=0x1217, dev=0x7114, revid=0x20
        bus=2, slot=6, func=1
        class=06-07-00, hdrtype=0x02, mfdev=1
        cmdreg=0x0080, statreg=0x0410, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=255
        powerspec 2  supports D0 D1 D2 D3  current D0
        map[10]: type 1, range 32, base d0208000, size 12, enabled
pcib2: matched entry for 2.6.INTA (source \_SB_.PCI0.LPC0.LNKB)
pcib2: slot 6 INTA is routed to irq 10
found-> vendor=0x1217, dev=0x7110, revid=0x00
        bus=2, slot=6, func=2
        class=08-80-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0103, statreg=0x0410, cachelnsz=8 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
        powerspec 2  supports D0 D1 D2 D3  current D0
        map[10]: type 1, range 32, base d0209000, size 11, enabled
        map[14]: type 1, range 32, base d0200000, size 14, enabled
pcib2: matched entry for 2.7.INTA (source \_SB_.PCI0.LPC0.LNKC)
pcib2: slot 7 INTA is routed to irq 10
found-> vendor=0x104c, dev=0x8026, revid=0x00
        bus=2, slot=7, func=0
        class=0c-00-10, hdrtype=0x00, mfdev=0
        cmdreg=0x0116, statreg=0x0210, cachelnsz=8 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns)
	intpin=a, irq=10
        powerspec 2  supports D0 D1 D2 D3  current D0
bfe0: <Broadcom BCM4401 Fast Ethernet> mem 0xd0204000-0xd0205fff irq 5 at device 2.0 on pci2
pcib2: device bfe0 requested decoded memory range 0xd0204000-0xd0205fff
bfe0: Ethernet address: 00:c0:9f:24:ac:fd
miibus0: <MII bus> on bfe0
bmtphy0: <BCM4401 10/100baseTX PHY> on miibus0
bmtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bfe0: bpf attached
pci2: <network> at device 4.0 (no driver attached)
cbb0: <PCI-CardBus Bridge> mem 0xd0207000-0xd0207fff at device 6.0 on pci2
pcib2: device cbb0 requested decoded memory range 0xd0207000-0xd0207fff
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib2: matched entry for 2.6.INTA (source \_SB_.PCI0.LPC0.LNKB)
pcib2: slot 6 INTA is routed to irq 10
cbb0: [MPSAFE]
cbb0: PCI Configuration space:
  0x00: 0x71141217 0x04100187 0x06070020 0x00824000
  0x10: 0xd0207000 0x020000a0 0x40000002 0xfffff000
  0x20: 0x00000000 0xfffff000 0x00000000 0x0000fffd
  0x30: 0x00000001 0x0000fffd 0x00000001 0x0740010a
  0x40: 0x001f1025 0x00000001 0x00000000 0x00000000
  0x50: 0x00000000 0x00000000 0x00000000 0x00000000
  0x60: 0x00000000 0x00000000 0x00000000 0x00000000
  0x70: 0x00000000 0x00000000 0x00000000 0x00000000
  0x80: 0x00000000 0x00000000 0x00000000 0x018c1882
  0x90: 0x02250003 0x00000000 0x00000000 0x00000000
  0xa0: 0xfe020001 0x00c04000 0x00000000 0x00000009
  0xb0: 0xfe020001 0x00c04000 0x00000000 0x00000009
  0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
  0xd0: 0x08004000 0x80810bea 0x00000000 0x00400000
  0xe0: 0x00820001 0x00000000 0x00000000 0x00000000
  0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
cbb1: <PCI-CardBus Bridge> at device 6.1 on pci2
pcib2: device cbb1 requested decoded memory range 0xd0200000-0xd05fffff
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
pcib2: matched entry for 2.6.INTA (source \_SB_.PCI0.LPC0.LNKB)
pcib2: slot 6 INTA is routed to irq 10
cbb1: [MPSAFE]
cbb1: PCI Configuration space:
  0x00: 0x71141217 0x04180087 0x06070020 0x00822000
  0x10: 0xd0200000 0x020000a0 0x20000000 0xfffff000
  0x20: 0x00000000 0xfffff000 0x00000000 0x0000fffd
  0x30: 0x00000001 0x0000fffd 0x00000001 0x0400010a
  0x40: 0x001f1025 0x00000001 0x00000000 0x00000000
  0x50: 0x00000000 0x00000000 0x00000000 0x00000000
  0x60: 0x00000000 0x00000000 0x00000000 0x00000000
  0x70: 0x00000000 0x00000000 0x00000000 0x00000000
  0x80: 0x00000000 0x00000000 0x00000000 0x018c1882
  0x90: 0x02250003 0x00000000 0x00000000 0x00000000
  0xa0: 0xfe020001 0x00c04000 0x00000000 0x00000008
  0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
  0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
  0xd0: 0x08004000 0x80820bea 0x00000000 0x10400000
  0xe0: 0x00820001 0x00000000 0x00000000 0x00000000
  0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
pci2: <base peripheral> at device 6.2 (no driver attached)
fwohci0: vendor=104c, dev=8026
fwohci0: <1394 Open Host Controller Interface> mem 0xd0200000-0xd0203fff,0xd0209000-0xd02097ff irq 10 at device 7.0 on pci2
fwohci0: latency timer 64 -> 64.
fwohci0: cache size 8 -> 8.
pcib2: device fwohci0 requested decoded memory range 0xd0209000-0xd02097ff
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 00:c0:9f:00:00:0a:5b:31
fwohci0: resetting OHCI...done (loop=0)
fwohci0: fwphy_rddata: 0x2 loop=0, retry=0
fwohci0: phy read failed(2).
fwohci0: fwphy_rddata: 0x3 loop=0, retry=1
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: fwphy_rddata: 0x5 loop=0, retry=0
fwohci0: Enable 1394a Enhancements
fwohci0: fwphy_rddata: 0x5 loop=0, retry=0
fwohci0: fwphy_rddata: 0x2 loop=0, retry=0
fwohci0: fwphy_rddata: 0x4 loop=0, retry=0
fwohci0: fwphy_rddata: 0x4 loop=0, retry=0
fwohci0: fwphy_rddata: 0x4 loop=0, retry=0
fwohci0: Link S400, max_rec 2048 bytes.
fwohci0: BUS_OPT 0xa002 -> 0xf800a002
fwohci0: fwohci_set_intr: 1
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:c0:9f:0a:5b:31
fwe0: bpf attached
sbp0: <SBP-2/SCSI over FireWire> on firewire0
sbp_attach (cold=1)
fwohci0: Initiate bus reset
fwohci0: fwphy_rddata: 0x1 loop=0, retry=0
fwohci0: fwphy_rddata: 0x1 loop=0, retry=0
fwohci0: BUS reset
sbp_post_busreset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
fwohci0: fw_set_bus_manager: 0->0 (loop=0)
firewire0: bus manager 0 (me)
send phy_config root_node=-1 gap_count=5
fwohci0: maxdesc: 2
fwohci0: start AT DMA status=0
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4 UDMA100 controller> port 0x1860-0x186f,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0-slave:  stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 mask=03 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: reset tp1 mask=03 ostat0=50 ostat1=00
ata1-master: stat=0x10 err=0x01 lsb=0x14 msb=0xeb
ata1-slave:  stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata1: reset tp2 mask=03 stat0=10 stat1=00 devices=0x4<ATAPI_MASTER>
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pci0: <multimedia, audio> at device 31.5 (no driver attached)
pci0: <simple comms> at device 31.6 (no driver attached)
acpi_lid0: <Contol Method Lid Switch> on acpi0
acpi_acad0: <AC Adapter> on acpi0
acpi_cmbat0: <Control Method Battery> on acpi0
acpi_cmbat1: <Control Method Battery> on acpi0
acpi_button0: <Sleep Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: unable to allocate IRQ
psmcpnp0 irq12 on acpi0
psm0: current command byte:0047
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 00 00 64
psm: status 00 03 64
psm: status 00 03 64
psm: data 08 00 00
psm: status 10 00 64
psm: status 00 02 64
psm: data 08 00 00
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
unknown: not probed (disabled)
acpi_ec0: <Embedded Controller: GPE 0x1d> port 0x66,0x62 on acpi0
ppc0: using extended I/O port range
ppc0: ECP SPP SPP
ppc0 port 0x778-0x77f,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
sio0: irq maps: 0x401 0x411 0x401 0x401
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1: irq maps: 0x401 0x409 0x401 0x401
sio1 port 0x2f8-0x2ff irq 3 drq 1 on acpi0
sio1: type 16550A
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
ex_isa_identify()
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xd0000-0xd17ff,0xc0000-0xcffff on isa0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
fdc0 failed to probe at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
vga0: vga: WARNING: video mode switching is not fully supported on this adapter
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 6f 4f 4f 93 56 84
9e 1f 00 4f 0d 0e 00 00 07 80 90 83 8f 28 1f 8f
9f a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 67 6f 4f 4f 93 56 84
9e 1f 00 4f 0d 0e 00 00 07 80 90 83 8f 28 1f 8f
9f a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 1298901389 Hz quality 800
Timecounters tick every 10.000 msec
lo0: bpf attached
ata1: spurious interrupt - status=0x00 error=0x01
Current DB 0
ch = 0
 Current OP   KEY INT BR   len     Addr   Depend Stat: Cnt
002c8000 OUTL ST2 ALL ALL    12 00000000 002c8080 8411:0008 RUN,ACTIVE, ack complete(11)
0x000000e0 0x00450000 0xffbaffff 0x00000000
bus_explore done
sbp_post_explore (sbp_cold=2)
ata0: spurious interrupt - status=0x50 error=0x00

(hangs)

Visit your host, monkey.org