wdc_atapi_intr_drq: Unexpectedly in the command phase. Please reportthis.

[Nico Foltinek <foltinen@camosun.bc.ca>]

dmesg follows
Installed 2.5 via CD, and CD device was found and mountable; no problem.
Installed 2.6 via ftp, and CD device is not found. I noticed the "please
report this" line in dmesg, so I sent it along. Maybe I'm just too new at
this, but I think this is why I can't get a /dev/acd0*.
Thanks.


OpenBSD 2.6 (GENERIC) #696: Tue Nov  2 01:46:05 MST 1999
    deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: F00F bug workaround installed
cpu0: Intel Pentium (P54C) ("GenuineIntel" 586-class) 133 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,MCE,CX8
BIOS mem  = 654336 conventional, 66060288 extended
real mem  = 66715648
avail mem = 57958400
using 840 buffers containing 3440640 bytes of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(90) BIOS, date 12/06/96
bios0: diskinfo 0xe055800c cksumlen 1 memmap 0xe0558088 pciinfo 0xe055810c apminfo 0xe0558128
apm0 at bios0: Power Management spec V1.1
apm0: AC on, no battery
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82437VX System (TVX)" rev 0x02
pcib0 at pci0 dev 7 function 0 "Intel 82371SB (Triton II) PCI-ISA" rev 0x01
pciide0 at pci0 dev 7 function 1 "Intel 82371SB (Triton II) IDE" rev 0x00: DMA, channel 0 wired to compatibility, channel 1 wired to compatibility
atapiscsi0 at pciide0 channel 0
scsibus0 at atapiscsi0: 2 targets
wdc_atapi_intr_drq: Unexpectedly in the command phase. Please report this.
wd0 at pciide0 channel 0 drive 0: <QUANTUM LIGHTNING 730A>
wd0: can use 32-bit, PIO mode 3, DMA mode 1
wd0: 8-sector PIO, LBA, 696MB, 1416 cyl, 16 head, 63 sec, 1427328 sectors
pciide0: channel 0 interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 0, DMA mode 1 (using DMA data transfers)
atapiscsi0(pciide0:0:1): using PIO mode 3
ep0 at pci0 dev 9 function 0 "3Com 3c595 100Base-TX" rev 0x00: address 00:a0:24:43:ef:05, utp/100-TX default utp/autoselect irq 10
ep1 at pci0 dev 10 function 0 "3Com 3c595 100Base-TX" rev 0x00: address 00:a0:24:9a:00:ed, utp/100-TX default utp/autoselect irq 11
"Cirrus Logic CL-GD5446" rev 0x00 at pci0 dev 12 function 0 not configured
isa0 at pcib0
isadma0 at isa0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
vt0 at isa0 port 0x60/16 irq 1: unknown Cirrus, 80 col, color, 8 scr, mf2-kbd
pms0 at vt0 irq 12
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask 4040 netmask 4c40 ttymask 5cc2
pctr: 586-class performance counters and user-level cycle counter enabled
dkcsum: wd0 matched BIOS disk 80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302