2.8 stable hangs :(

[Timur Maryin <tima@east.ru>]

Hello!

Year ago i installed OpenBSD 2.6
It was up for 363 days (!)

In january i started to prepare new 2.8 based system.
As you know, several bugs in named appears some time later.
After applying the patch on new system, binary `named' still contains old `REL' string
(4.9.7)
(but in Makefile it was proper - 4.9.8), so i decided to use cvsup.

After succsessful cvsup (2.8 -stable), and new kernel installed, named still 
have old `REL' :) but it's not a topic of message :)
==
tima@sentry>strings /usr/sbin/named |grep REL
named 4.9.7-REL Thu May 21 19:27:54 1998
4.9.7-REL
==


I shutted down 2.6 system (Aahh :), replaced old disc and controller with new ones (with
2.8).
The problem is that new system hangs after several days.
i.e. i can successfully ping eth interface or establish tcp connection, but nothing else.
System does not respond even from console!
And nothing in logs. They just stop.
So, i can only use `reset' button :(

This repeats three times within last week! :(
Now system is up for 3 days...



The main services on system is named, tacacs and gated (3.5.11).
tacacs is ok. It's the same as on my 2.6 based system.
Gated too ...
And i sure, that mrtg (perl), bb, and apache (1.3.14) can't cause such problems.



Hardware differencies from 2.6 system (that was up for almost year) is one scsi hard disk
and scsi controller.
Old was:
==
ahc0 at pci0 dev 14 function 0 "Adaptec AHA-2940U" rev 0x01: irq 11
ahc0: aic7880 Wide Channel, SCSI Id=7, 16 SCBs
scsibus0 at ahc0: 16 targets
ahc0: target 0 using 16Bit transfers
ahc0: target 0 synchronous at 20.0MHz, offset = 0x8
sd0 at scsibus0 targ 0 lun 0: <IBM, DNES-309170W, SA30> SCSI3 0/direct fixed
sd0: 8748MB, 11474 cyl, 5 head, 312 sec, 512 bytes/sec, 17916240 sec total
==

Current config listed below.


I'm not think, that it's an overheat problem.


Can somebody help me? :)
Thanks, sorry for poor english :)



P.S. Also i have problems with `make obj' in /usr/src/
Somewhere in src/usr.bin/tic.
Seems, that incorrect paths in `MKtermsort.sh'. In current tree it was corrected, but
i couldn't compile the kernel (so i rollback to -stable).



P.P.S
some additional info
my supfile:
== cut ==
...
*default host=cvsup.hu.OpenBSD.org
#*default host=cvsup.uk.OpenBSD.org
*default base=/var
*default prefix=/usr
*default tag=OPENBSD_2_8
*default umask=002
*default release=cvs
*default delete use-rel-suffix

# If your network link is a T1 or faster, comment out the following line.
*default compress

# Main Source Tree.
OpenBSD-src
== cut ==


dmesq:


OpenBSD 2.8-stable (SENTRY) #0: Fri Mar 23 14:12:03 MSK 2001
    tima@sentry:/usr/src/sys/arch/i386/compile/SENTRY
cpu0: Intel Pentium II (Celeron) ("GenuineIntel" 686-class, 128KB L2 cache) 434 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SYS,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR
real mem  = 268009472 (261728K)
avail mem = 246091776 (240324K)
using 3297 buffers containing 13504512 bytes (13188K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(83) BIOS, date 10/19/99, BIOS32 rev. 0 @ 0xf06b0
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
pcibios0 at bios0: rev. 2.1 found at 0xf0000[0xf12]
pcibios0: PCI IRQ Routing Table rev. 1.0 found at 0xf0e70, size 160 bytes (8 entries)
pcibios0: PCI Interrupt Router at 000:04:0 ("Intel 82371FB (Triton) PCI-ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82443BX PCI-AGP" rev 0x03
ppb0 at pci0 dev 1 function 0 "Intel 82443BX AGP" rev 0x03
pci1 at ppb0 bus 1
pcib0 at pci0 dev 4 function 0 "Intel 82371AB PIIX4 ISA" rev 0x02
pciide0 at pci0 dev 4 function 1 "Intel 82371AB IDE (PIIX4)" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 
wired to compatibility
wd0 at pciide0 channel 0 drive 0: <IBM-DTLA-307020>
wd0: can use 32-bit, PIO mode 4, DMA mode 2, Ultra-DMA mode 2
wd0: 16-sector PIO, LBA, 19623MB, 16383 cyl, 16 head, 63 sec, 40188960 sectors
pciide0: channel 0 interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (using DMA data transfers)
atapiscsi0 at pciide0 channel 1
scsibus0 at atapiscsi0: 2 targets
scsibus0 targ 0 lun 0: <ASUS, CD-S450/A, 3.1H> SCSI0 5/cdrom removable not configured
pciide0: channel 1 interrupting at irq 15
atapiscsi0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (using DMA data transfers)
"Intel 82371AB USB (PIIX4)" rev 0x01 at pci0 dev 4 function 2 not configured
"Intel 82371AB Power Management (PIIX4)" rev 0x02 at pci0 dev 4 function 3 not configured
fxp0 at pci0 dev 10 function 0 "Intel 82557" rev 0x05: irq 10, address 00:08:c7:8c:fc:d9
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 0
de0 at pci0 dev 11 function 0 "DEC DECchip 21142/3" rev 0x30: irq 11
de0: 21143 [10-100Mb/s] pass 3.0 address 00:80:48:e7:19:d2
ahc0 at pci0 dev 13 function 0 "Adaptec AHA-2940U" rev 0x01: irq 12
ahc0: Wide Channel A, SCSI Id=7, 16/255 SCBs
scsibus1 at ahc0: 16 targets
ahc0: target 1 using 16bit transfers
ahc0: target 1 synchronous at 20.0MHz, offset = 0x8
sd0 at scsibus1 targ 1 lun 0: <IBM, DDYS-T09170N, S80D> SCSI3 0/direct fixed
sd0: 8748MB, 15110 cyl, 3 head, 395 sec, 512 bytes/sec, 17916240 sec total
isa0 at pcib0
isadma0 at isa0
pcppi0 at isa0 port 0x61
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
vt0 at isa0 port 0x60/16 irq 1: vga 80/132 col, color, 8 scr, mf2-kbd
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask d040 netmask dc40 ttymask dcc2
pctr: 686-class user-level performance counters enabled
dkcsum: wd0 matched BIOS disk 81
dkcsum: sd0 matched BIOS disk 80
root on sd0a
rootdev=0x400 rrootdev=0xd00 rawdev=0xd02
WARNING: / was not properly unmounted
de0: enabling 10baseT port
de0: abnormal interrupt: receive process stopped




-- 
Timur Maryin
East Connection ISP (http://www.east.ru)