[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Using Drive: 0 Partition 3 .....

Greetings,


I've just installed OpenBSD 3.0 on a Compaq Prosigna 200 (System BIOS
P05 12/30/1998), 300 MHZ PII, 128 MB RAM (no Compaq System Partition
Utilities` are available on this system).  The system boots with the
following SCSI/ATAPI/PCI/ISA components:

.....

siop0 at pci0 dev 13 function 0 "Symbios Logic 53c875" rev 0x04: irq 11 has RAM
scibus0 at siop0: 16targets

.....

sd0at scsibus0targ0 lun0: <IBM, DPSS-318350N, S96H> SCSI3 0/direct fixed
siop0: target 0 now using tagged 16 20 Mhz 16 REQ/ACK offset xfers
sd0: 17501MB, 14627 cyl, 5 head, 490 sec, 512 bytes/sec, 35843670 sec total

.....

st0: at scsibus0 targ 2 lun0: <SONY, STD-7000, 0300> SCSI2
1/sequentialremovable
st0: siop0: target 2 now using 8bit 10 Mhz 15 REQ/ACK offset xfers
drive empty

.....

fxp0 at pci0 dev 11 function 0 "Intel 82557" rev 0x08: irq 10,
address 00:90:27:8e:64:cf

.....

tl0 at pci0 dev 16 function 0 "Compaq Integrated NetFlex 3/P"
rev qx10: irq 11 address  0:08:c7:5c:52:98

.....

vga1 at pci0 dev 12  function 0 "ATI Mach64 CT" rev 0x09
wsdisplay0 at vga1: console (80x25, vt100 emulation)

.....

atapiscsi0 at pciide0channel 1 drive 0
scsibus1 at atapiscsi0: 2targets
cd0 at scsibus1 targ 0 lun 0: <COMPAQ, CRD-8241B, 1.17> SCSI0 5/cdrom removable
cd0(pciide0:1:0):using PIO mode 4

.....

pckbd0 at isa0 port 0x60/5
pckbd0 at pckbdc0 port (kbd slot)
pckbd0: using irq 1 for kbd slot
wskbd at pckbd0: console keyboard, using wsdisplay0

.....

pccom0 at isa0 port 0x3f8/8 irq4: ns16550a, 16 byte fifo

pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo

.....

fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2head, 18 sec

.....

fdisk:

fdisk /dev/rsd0c
Disk: /dev/rsd0c	geometry: 2231/255/63 [35841015 sectors]
Only LBA values are valid in ending cylinder for partition #3.
Offset: 0	Signatures: 0xAA55,0x0

		Starting		Ending
 #:	id	cyl	hd	sec  -	cyl	hd	sec [start -	size]
 0:	00	0	0	0     -	0	0	0   [	0   -	0]	unused
 1:	00	0	0	0     -	0	0	0   [	0   -	0] 	unused
 2:	00	0	0	0     -	0	0	0   [	0   -	0] 	unused
*3	A6	0	1	1     -	1023	254	63  [	63 -35840952]	OpenBSD

disklabel/mount points:

> p
device: /dev/rsd0c
type: SCSI
disk: SCSI disk
label: DPSS-318350N
bytes/sector: 512
sectors/track: 490
Tracks/cylinder: 5
sectors/cylinder: 2450
cylinders: 14627
total sectors: 35843670
free sectors: 0
rpm 3600

16 partitions:

#	size		offset		fstype	[fsize	bsize	cpg]
a:	4194337		63		4.2BSD	1024	8192	16   #	/
b:	1048600		4194400		swap
c:	35843670	0		unused	0	0
d:	1048600		5243000		4.2BSD	1024	8192	16   #	/tmp
e:	8388800		6291600		4.2BSD	1024	8192	16   #	/usr
f:	8388800		14680400	4.2BSD	1024	8192	16   #	/usr/local
g:	8388800		23069200	4.2BSD	1024	8192	16   #	/var
h:	4383015		31458000	4.2BSD	1024	8192	16   #	/home

.....

After halt/reboot I am getting the following message:

	Using Drive: 0 Partition: 3

however, OpenBSD (3.0) is not loading.

Any suggestions, please?

Regards,

Ioan