hme0 trouble on Sun Netra T1/105

["Anders B Jansson" <hdw@kallisti.se>]

Hoping to get rid of Solaris on yet another pack of machines I installed 3.0
on a Netra T1/105.
Everythings looks good except for the onboard hme interfaces.
It does find the interface during boot, and I can configure it.
But as soon as I try to use it I get 'ra /bsd: hme0: device timeout'.
And then it continues to log that until reboot.

Looking at the dmesg I noticed that it seems to fail identifying the hardware correctly.
>hme0 at pci1 dev 1 function 1 "Sun HME" rev 0x01: address 08:00:20:b2:d6:3f
>ukphy0 at hme0 phy 0: Generic IEEE 802.3u media interface
>ukphy0: OUI 0x00601d, model 0x000c, rev. 1
>ukphy1 at hme0 phy 1: Generic IEEE 802.3u media interface
>ukphy1: OUI 0x00601d, model 0x000c, rev. 1
>hme0: using ivec 3021 for interrupt

If I understand it rigth, it should have been nsphy* instead of ukphy*.

I've tried with the lastest snapshot, with the same result.
Anyone got it running on a T1?

// hdw
dmesg:
OpenBSD 3.0 (GENERIC) #27: Wed Oct 17 17:49:00 MDT 2001
    deraadt@sparc64:/usr/src/sys/arch/sparc64/compile/GENERIC
total memory = 536870912
avail memory = 504897536
using 200 buffers containing 13107200 of memory
bootpath: /pci@1f,0/pci@1,1/scsi@2,0/disk@0,0
mainbus0 (root): SUNW,UltraSPARC-IIi-cEngine
cpu0 at mainbus0: SUNW,UltraSPARC-IIi @ 360.007 MHz, version 0 FPU
cpu0: physical 4K instruction (32 b/l), 4K data (32 b/l), 2048K external (64 b/l) 
psycho0 at mainbus0 addr 0xfffc0000
SUNW,sabre: impl 0, version 0: ign 7c0 bus range 0 to 3; PCI bus 0
DVMA map: c0000000 to e0000000
pci0 at psycho0
ppb0 at pci0 dev 1 function 1 "Sun Simba PCI-PCI" rev 0x13
pci1 at ppb0 bus 1
ebus0 at pci1 dev 1 function 0 "Sun PCIO Ebus2" rev 0x01
auxio0 at ebus0 addr 726000-726003, 728000-728003, 72a000-72a003, 72c000-72c003, 72f000-72f003
power at ebus0 addr 724000-724003 ipl 37 not configured
SUNW,pll at ebus0 addr 504000-504002 not configured
su at ebus0 addr 3803f8-3803ff ipl 28 not configured
su at ebus0 addr 3602f8-3602ff ipl 20 not configured
ecpp at ebus0 addr 340278-340287, 30015c-30015d, 700000-70000f ipl 34 not configured
fdthree at ebus0 addr 3203f0-3203f7, 706000-70600f, 720000-720003 ipl 39 not configured
clock0 at ebus0 addr 0-1fff: mk48t59: hostid 80b2d63f
flashprom at ebus0 addr 0-fffff not configured
watchdog at ebus0 addr 200000-20003f ipl 4 not configured
display7seg at ebus0 addr 200040-200040 not configured
beeper0 at ebus0 addr 722000-722003
flashprom at ebus0 addr 400000-5fffff not configured
flashprom at ebus0 addr 800000-9fffff not configured
i2c at ebus0 addr 600000-600003 ipl 40 not configured
i2c at ebus0 addr 100000-100003 ipl 27 not configured
SUNW,lom at ebus0 addr 400000-400063 not configured
hme0 at pci1 dev 1 function 1 "Sun HME" rev 0x01: address 08:00:20:b2:d6:3f
ukphy0 at hme0 phy 0: Generic IEEE 802.3u media interface
ukphy0: OUI 0x00601d, model 0x000c, rev. 1
ukphy1 at hme0 phy 1: Generic IEEE 802.3u media interface
ukphy1: OUI 0x00601d, model 0x000c, rev. 1
hme0: using ivec 3021 for interrupt
siop0 at pci1 dev 2 function 0 "Symbios Logic 53c875" rev 0x03: ivec 20, has RAM
scsibus0 at siop0: 16 targets
sd0 at scsibus0 targ 0 lun 0: <SEAGATE, ST318203LSUN18G, 034A> SCSI2 0/direct fixed
siop0: target 0 now using tagged 16 bit 20 MHz 15 REQ/ACK offset xfers
sd0: 17274MB, 7508 cyl, 19 head, 248 sec, 512 bytes/sec, 35378533 sec total
ppb1 at pci0 dev 1 function 0 "Sun Simba PCI-PCI" rev 0x13
pci2 at ppb1 bus 2
ppb2 at pci2 dev 1 function 0 "DEC 21150 PCI-PCI" rev 0x04
pci3 at ppb2 bus 3
pciide0 at pci3 dev 14 function 0 "CMD Technology PCI0646" rev 0x03: DMA, channel 0 configured to native-PCI, channel 1 configured to native-PCI
pciide0: using ivec 1800 for native-PCI interrupt
"Realtek 8139" rev 0x10 at pci3 dev 15 function 0 not configured
pcons0 at mainbus0
No counter-timer -- using %tick at 360MHz as system clock.
root on sd0a
rootdev=0x700 rrootdev=0x1100 rawdev=0x1102
WARNING: / was not properly unmounted