[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: recommend good non-raid SCSI card?
Sorry for break in. I am using AHA-29160 with more than one drives, HP
surestore-5000, and SCSI CD-ROM with no problem. Here is my dmesg. I do
think there is some other problem with your system.
Clarence
======= dmesg =======
OpenBSD 3.1-current (GENERIC) #3: Sat Jun 1 22:54:38 HKT 2002
root@OBSD-C:/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium III (Coppermine) ("GenuineIntel" 686-class) 702 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SYS,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SIMD
real mem = 266907648 (260652K)
avail mem = 241713152 (236048K)
using 3283 buffers containing 13447168 bytes (13132K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(56) BIOS, date 02/06/02, BIOS32 rev. 0 @ 0xfb420
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
pcibios0 at bios0: rev. 2.1 @ 0xf0000/0xd9d4
pcibios0: PCI IRQ Routing Table rev. 1.0 @ 0xfd970/80 (3 entries)
pcibios0: PCI Exclusive IRQs: 5 11 12
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371SB PCI-ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0xa000 0xcc000/0x6600
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82815 Hub" rev 0x02: rng active, 9Kb/sec
vga1 at pci0 dev 2 function 0 "Intel 82815 Graphics" rev 0x02
wsdisplay0 at vga1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ppb0 at pci0 dev 30 function 0 "Intel 82801AA Hub-to-PCI" rev 0x02
pci1 at ppb0 bus 1
ahc0 at pci1 dev 3 function 0 "Adaptec AHA-29160 U160" rev 0x02: irq 11
ahc0: Wide Channel A, SCSI Id=7, 16/255 SCBs
scsibus0 at ahc0: 16 targets
ahc0: target 0 using 16bit transfers
ahc0: target 0 synchronous at 40.0MHz, offset = 0x3f
ahc0: target 0 using tagged queuing
sd0 at scsibus0 targ 0 lun 0: <IBM, DDYS-T18350N, S96H> SCSI3 0/direct fixed
sd0: 17501MB, 15110 cyl, 6 head, 395 sec, 512 bytes/sec, 35843670 sec total
ahc0: target 1 using 16bit transfers
ahc0: target 1 synchronous at 40.0MHz, offset = 0x3f
ahc0: target 1 using tagged queuing
sd1 at scsibus0 targ 1 lun 0: <IBM, DDYS-T09170N, S96H> SCSI3 0/direct fixed
sd1: 8748MB, 15110 cyl, 3 head, 395 sec, 512 bytes/sec, 17916240 sec total
ahc0: target 3 using 8bit transfers
ahc0: target 3 synchronous at 5.0MHz, offset = 0x8
st0 at scsibus0 targ 3 lun 0: <HP, HP35480A, T603> SCSI2 1/sequential removable
st0: density code 0x13, variable blocks, write-enabled
ahc0: target 6 using 8bit transfers
ahc0: target 6 synchronous at 10.0MHz, offset = 0xf
cd0 at scsibus0 targ 6 lun 0: <PLEXTOR, CD-ROM PX-20TS, 1.00> SCSI2 5/cdrom removable
rl0 at pci1 dev 5 function 0 "Realtek 8139" rev 0x10: irq 12 address 00:00:21:c0:ec:b7
rlphy0 at rl0 phy 0: RTL internal phy
pcib0 at pci0 dev 31 function 0 "Intel 82801AA LPC" rev 0x02
pciide0 at pci0 dev 31 function 1 "Intel 82801AA IDE" rev 0x02: DMA, channel 0 wired to compatibility, channel 1 wired to compatibility
uhci0 at pci0 dev 31 function 2 "Intel 82801AA USB" rev 0x02: irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x0000 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
"Intel 82801AA SMBus" rev 0x02 at pci0 dev 31 function 3 not configured
auich0 at pci0 dev 31 function 5 "Intel 82801AA AC97 Audio" rev 0x02: irq 12 ICH AC97
ac97: codec id 0x83847644 (SigmaTel STAC9744/45)
ac97: codec features 18 bit DAC, 18 bit ADC, SigmaTel 3D
audio0 at auich0
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask 840 netmask 1840 ttymask 18c2
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
Kernelized RAIDframe activated
dkcsum: sd0 matched BIOS disk 80
dkcsum: sd1 matched BIOS disk 81
root on sd0a
rootdev=0x400 rrootdev=0xd00 rawdev=0xd02
======================
On Sun, 2 Jun 2002, OpenBSD baby wrote:
> > I'm first curious why your 29160 can't work with more than
> > one drive. Perhaps you're having some OTHER problem?
>
> Nope - it's a known problem.
> Theo & the author of the ahc driver know about it.
> smurph@openbsd.org is working on it. It's a tough one.
>
> On http://www.openbsd.org/i386.html it says down by
> "products like the AHA-29160"...
>
> "(However, the 7899G card is currently not
> supported with more than one device attached)"
>
> Like an idiot, I bought 3 of these cards before seeing
> that "fine print".
>
> :-)