[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
PCMCIA on Vaio R505TL
Hello,
I'm trying to use a laptop I have laying around as my home firewall/router/DNS
server/etc, but can't get OpenBSD to recognize the PCMCIA ethernet card I was
hoping to use as the 2nd NIC. I have slightly more experience than a total
newbie, having used OpenBSD since 2.9, but have never have tried using it on
anything but vanilla i386 hardware, so I've never run into any issues like this.
I've checked the i386 laptops page, but nothing in the same family of laptops is
listed (probably a bad sign for me). The ethernet card is on the supported
hardware list (Linksys PCMPC200 CardBus 10/100).
A couple searches on Google pointed me at a few threads where people were having
similar issues with other laptops, but the threads always came to a close
without a solution being presented. Just a lot of "works for me" type
responses.
This laptop only has a single PCMCIA slot, and the only two PCMCIA devices I
have are an external CD-ROM and the ethernet card I'm trying to use. I used the
external CD-ROM to boot off the CD and installed 3.3. I had to do an FTP install
since the install script couldn't read the files off the CD (my first sign of
trouble looming), despite having booted and loaded the install script off of
that very drive. I don't recall exactly what the message said...
Please reply to misc@ - I don't check this account for incoming mail.
Thanks,
Matt
dmesg:
OpenBSD 3.3 (GENERIC) #44: Sat Mar 29 13:22:05 MST 2003
deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium III (Coppermine) ("GenuineIntel" 686-class, 128KB L2 cache)
646 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SYS,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SIMD
real mem = 132161536 (129064K)
avail mem = 116871168 (114132K)
using 1638 buffers containing 6709248 bytes (6552K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(c9) BIOS, date 06/26/01, BIOS32 rev. 0 @ 0xfd878
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
pcibios0 at bios0: rev. 2.1 @ 0xfd860/0x7a0
pcibios0: PCI IRQ Routing Table rev. 1.0 @ 0xfdf30/176 (9 entries)
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371FB PCI-ISA" rev 0x00)
pcibios0: PCI bus #2 is the last bus
bios0: ROM list: 0xc0000/0xc000 0xd8000/0x4000! 0xdc000/0x4000!
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82815 Hub" rev 0x11: rng active, 7Kb/sec
vga1 at pci0 dev 2 function 0 "Intel 82815 Graphics" rev 0x11: aperture at
0xf8000000, size 0x4000000
wsdisplay0 at vga1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ppb0 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0x03
pci1 at ppb0 bus 1
"Texas Instruments TSB43AA22 FireWire" rev 0x02 at pci1 dev 0 function 0 not
configured
cbb0 at pci1 dev 2 function 0 "Ricoh 5C475 PCI-CardBus" rev 0x80pci_intr_map: no
mapping for pin A
: couldn't map interrupt
fxp0 at pci1 dev 8 function 0 "Intel 82562" rev 0x03: irq 9, address
08:00:46:17:c3:cf
inphy0 at fxp0 phy 1: i82562ET 10/100 media interface, rev. 0
pcib0 at pci0 dev 31 function 0 "Intel 82801BAM LPC" rev 0x03
pciide0 at pci0 dev 31 function 1 "Intel 82801BAM IDE" rev 0x03: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <HITACHI_DK23BA-15>
wd0: 16-sector PIO, LBA, 14403MB, 16383 cyl, 16 head, 63 sec, 29498112 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4
pciide0: channel 1 ignored (disabled)
uhci0 at pci0 dev 31 function 2 "Intel 82801BA USB" rev 0x03: irq 9
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x0000 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
"Intel 82801BA SMBus" rev 0x03 at pci0 dev 31 function 3 not configured
uhci1 at pci0 dev 31 function 4 "Intel 82801BA USB2" rev 0x03: irq 9
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: vendor 0x0000 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
auich0 at pci0 dev 31 function 5 "Intel 82801BA AC97 Audio" rev 0x03: irq 9,
ICH2 AC97
ac97: codec id 0x41445348 (Analog Devices AD1881A)
ac97: codec features headphone, Analog Devices Phat Stereo
audio0 at auich0
"Intel 82801BA AC97 Modem" rev 0x03 at pci0 dev 31 function 6 not configured
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
biomask 4200 netmask 4200 ttymask 5282
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: wd0 matched BIOS disk 80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
umass0 at uhub1 port 1 configuration 1 interface 0
umass0: Sony USB Memory Stick Slot, rev 1.10/1.80, addr 2
umass0: using SFF8070i over CBI-I
scsibus0 at umass0: 2 targets
sd0 at scsibus0 targ 1 lun 0: <Sony, MSC-U02, 1.00> SCSI0 0/direct removable
sd0: drive offline
syncing disks... done
rebooting...
OpenBSD 3.3 (GENERIC) #44: Sat Mar 29 13:22:05 MST 2003
deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium III (Coppermine) ("GenuineIntel" 686-class, 128KB L2 cache)
646 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SYS,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SIMD
real mem = 132161536 (129064K)
avail mem = 116871168 (114132K)
using 1638 buffers containing 6709248 bytes (6552K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(8a) BIOS, date 06/26/01, BIOS32 rev. 0 @ 0xfd878
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
pcibios0 at bios0: rev. 2.1 @ 0xfd860/0x7a0
pcibios0: PCI IRQ Routing Table rev. 1.0 @ 0xfdf30/176 (9 entries)
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371FB PCI-ISA" rev 0x00)
pcibios0: PCI bus #2 is the last bus
bios0: ROM list: 0xc0000/0xc000 0xd8000/0x4000! 0xdc000/0x4000!
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82815 Hub" rev 0x11: rng active, 7Kb/sec
vga1 at pci0 dev 2 function 0 "Intel 82815 Graphics" rev 0x11: aperture at
0xf8000000, size 0x4000000
wsdisplay0 at vga1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ppb0 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0x03
pci1 at ppb0 bus 1
"Texas Instruments TSB43AA22 FireWire" rev 0x02 at pci1 dev 0 function 0 not
configured
cbb0 at pci1 dev 2 function 0 "Ricoh 5C475 PCI-CardBus" rev 0x80pci_intr_map: no
mapping for pin A
: couldn't map interrupt
fxp0 at pci1 dev 8 function 0 "Intel 82562" rev 0x03: irq 9, address
08:00:46:17:c3:cf
inphy0 at fxp0 phy 1: i82562ET 10/100 media interface, rev. 0
pcib0 at pci0 dev 31 function 0 "Intel 82801BAM LPC" rev 0x03
pciide0 at pci0 dev 31 function 1 "Intel 82801BAM IDE" rev 0x03: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <HITACHI_DK23BA-15>
wd0: 16-sector PIO, LBA, 14403MB, 16383 cyl, 16 head, 63 sec, 29498112 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4
pciide0: channel 1 ignored (disabled)
uhci0 at pci0 dev 31 function 2 "Intel 82801BA USB" rev 0x03: irq 9
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x0000 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
"Intel 82801BA SMBus" rev 0x03 at pci0 dev 31 function 3 not configured
uhci1 at pci0 dev 31 function 4 "Intel 82801BA USB2" rev 0x03: irq 9
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: vendor 0x0000 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
auich0 at pci0 dev 31 function 5 "Intel 82801BA AC97 Audio" rev 0x03: irq 9,
ICH2 AC97
ac97: codec id 0x41445348 (Analog Devices AD1881A)
ac97: codec features headphone, Analog Devices Phat Stereo
audio0 at auich0
"Intel 82801BA AC97 Modem" rev 0x03 at pci0 dev 31 function 6 not configured
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
biomask 4200 netmask 4200 ttymask 5282
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: wd0 matched BIOS disk 80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
umass0 at uhub1 port 1 configuration 1 interface 0
umass0: Sony USB Memory Stick Slot, rev 1.10/1.80, addr 2
umass0: using SFF8070i over CBI-I
scsibus0 at umass0: 2 targets
sd0 at scsibus0 targ 1 lun 0: <Sony, MSC-U02, 1.00> SCSI0 0/direct removable
sd0: drive offline
------------------------------------------------------------
Visit the world's greatest site at http://www.farts.com and listen to the fart
of the day. Also, get your very own farts.com E-mail account. FREE!!!!!
---------------------------------------------------------------------
Express yourself with a super cool email address from BigMailBox.com.
Hundreds of choices. It's free!
http://www.bigmailbox.com
---------------------------------------------------------------------