Re: nic initialization

[marmango <marmango@softhome.net>]

marmango wrote:
> I have just installed openbsd 3.4 on my laptop. It's an HP Omnibook XE3.
> I managed to configure XFree86, so far.
> My NIC has a strange behaviour:
> If I try to boot normaly the system freezes at the network initialization.
> But if I boot in single user, then I can configure the nic (dc0) without 
> any problems by using ifconfig.
> If instead I do sh -x /etc/netstart it freezes at ifstart dc0.
> What may be the problem? I see from dmesg that it assigns irq 11 to dc0 
> and also to the PCI-CardBus cbb0 and cbb1.
> Is there any simple way to change this?
> 

> OpenBSD 3.4 (GENERIC) #18: Wed Sep 17 03:34:47 MDT 2003
>     deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
> cpu0: Intel Pentium III (Coppermine) ("GenuineIntel" 686-class) 697 MHz
> cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SIMD
> real mem  = 133738496 (130604K)
> avail mem = 118059008 (115292K)
> using 1658 buffers containing 6791168 bytes (6632K) of memory
> mainbus0 (root)
> bios0 at mainbus0: AT/286+(9c) BIOS, date 05/22/01, BIOS32 rev. 0 @ 0xfd8a0
> apm0 at bios0: Power Management spec V1.2
> apm0: battery life expectancy 100%
> apm0: AC on, battery charge high, estimated 3:20 hours
> pcibios0 at bios0: rev. 2.1 @ 0xfd8a0/0x760
> pcibios0: PCI IRQ Routing Table rev. 1.0 @ 0xfdf50/144 (7 entries)
> pcibios0: PCI Interrupt Router at 000:07:0 ("Intel 82371FB PCI-ISA" rev 0x00)
> pcibios0: PCI bus #3 is the last bus
> bios0: ROM list: 0xc0000/0xc000 0xdc000/0x4000!
> pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
> pchb0 at pci0 dev 0 function 0 "Intel 82443BX PCI-AGP" rev 0x03
> ppb0 at pci0 dev 1 function 0 "Intel 82443BX AGP" rev 0x03
> pci1 at ppb0 bus 1
> vga1 at pci1 dev 1 function 0 "S3 Savage/IX-MV" rev 0x13
> wsdisplay0 at vga1: console (80x25, vt100 emulation)
> wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
> cbb0 at pci0 dev 4 function 0 "Texas Instruments PCI1420 PCI-CardBus" rev 0x00: irq 11
> cbb1 at pci0 dev 4 function 1 "Texas Instruments PCI1420 PCI-CardBus" rev 0x00: irq 11
> pcib0 at pci0 dev 7 function 0 "Intel 82371AB PIIX4 ISA" rev 0x02
> pciide0 at pci0 dev 7 function 1 "Intel 82371AB IDE" rev 0x01: DMA, channel 0 wired to compatibility, channel 1 wired to compatibility
> wd0 at pciide0 channel 0 drive 0: <IC25N040ATMR04-0>
> wd0: 16-sector PIO, LBA48, 38154MB, 16383 cyl, 16 head, 63 sec, 78140160 sectors
> wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
> atapiscsi0 at pciide0 channel 1 drive 0
> scsibus0 at atapiscsi0: 2 targets
> cd0 at scsibus0 targ 0 lun 0: <TEAC, CD-W24E, 1.0A> SCSI0 5/cdrom removable
> cd0(pciide0:1:0): using PIO mode 4, DMA mode 2
> uhci0 at pci0 dev 7 function 2 "Intel 82371AB USB" rev 0x01: irq 5
> usb0 at uhci0: USB revision 1.0
> uhub0 at usb0
> uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> "Intel 82371AB Power Mgmt" rev 0x03 at pci0 dev 7 function 3 not configured
> esa0 at pci0 dev 8 function 0 "ESS ES1989" rev 0x12: irq 5
> ac97: codec id 0x45838308 (ESS Technology ES1921)
> ac97: codec features 20 bit DAC, 20 bit ADC, ESS Technology
> audio0 at esa0
> "ESS ES1989 Modem" rev 0x12 at pci0 dev 8 function 1 not configured
> dc0 at pci0 dev 16 function 0 "Accton Technology EN2242" rev 0x11: irq 11, address 00:d0:59:54:04:4e
> ukphy0 at dc0 phy 1: Generic IEEE 802.3u media interface
> ukphy0: OUI 0x000895, model 0x0001, rev. 0
> cardslot0 at cbb0 slot 0 flags 0
> cardbus0 at cardslot0: bus 2 device 0 cacheline 0x0, lattimer 0x20
> pcmcia0 at cardslot0
> cardslot1 at cbb1 slot 1 flags 0
> cardbus1 at cardslot1: bus 3 device 0 cacheline 0x0, lattimer 0x20
> pcmcia1 at cardslot1
> isa0 at pcib0
> isadma0 at isa0
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard, using wsdisplay0
> pms0 at pckbc0 (aux slot)
> pckbc0: using irq 12 for aux slot
> wsmouse0 at pms0 mux 0
> pcppi0 at isa0 port 0x61
> midi0 at pcppi0: <PC speaker>
> sysbeep0 at pcppi0
> lpt0 at isa0 port 0x378/4 irq 7
> npx0 at isa0 port 0xf0/16: using exception 16
> pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
> fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
> fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
> biomask c860 netmask c860 ttymask d8e2
> pctr: 686-class user-level performance counters enabled
> mtrr: Pentium Pro MTRR support
> dkcsum: wd0 matched BIOS disk 80
> root on wd0a
> rootdev=0x0 rrootdev=0x300 rawdev=0x302
> WARNING: / was not properly unmounted
> pccom3 at pcmcia0 function 0 "3Com Megahertz, 3CXM756/3CCM756" port 0xa3f8/8: ns16450, no fifo
> uhidev0 at uhub0 port 1 configuration 1 interface 0
> uhidev0: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM), rev 1.10/3.00, addr 2, iclass 3/1
> ums0 at uhidev0: 5 buttons and Z dir.
> wsmouse1 at ums0 mux 0
> umass0 at uhub0 port 2 configuration 1 interface 0
> umass0: TRANSCEND TS0MHDENC, rev 2.00/0.02, addr 3
> umass0: using SCSI over Bulk-Only
> scsibus1 at umass0: 2 targets
> sd0 at scsibus1 targ 1 lun 0: <IBM-DJSA, -210, 0811> SCSI0 0/direct fixed
> umass_scsi_cb: status cmd failed for scsi op 0x1b
> sd0: 9590MB, 9590 cyl, 64 head, 32 sec, 512 bytes/sec, 19640880 sec total
> WARNING: R/W mount of /home denied.  Filesystem is not clean - run fsck
> WARNING: R/W mount of /usr denied.  Filesystem is not clean - run fsck

 > /etc/hostname_dc0 ->
> inet 192.168.0.2 255.255.255.0 NONE 
> 

This is a follow-up.
I tried booting having disabled pcibios (thanks to davids@idiom.com)
and it worked. The network (nic) now starts without problem.
But another problem come up as a result of the disabled pcibios
option: the pcmcia modem (the one you see in the dmesg before disabling 
pcibios) is not detected (probed?) any more. It' a modem I have been 
using with linux without problems. I know it's an ns16550a not an 
ns16450, and what does "no fifo" mean?
How can I set it up in openbsd (3.4 relase)?

PS: And another question please:
How can I turn down the volume level of the system bell, cause it sounds 
at its maximum, either in X or in console.