Re: 3.6 snapshot from 08/27/04 hangs after boot

[Otto Moerbeek <otto@drijf.net>]

On Wed, 1 Sep 2004, Sascha Hanse wrote:

> On Wed, 1 Sep 2004 14:28:11 +0200
> Sascha Hanse <sensei@bsdberlin.org> wrote:
> 
> > Hi,
> > 
> > I wanted to upgrade my 3.5 Box to 3.6, so I used the cd36.iso to make
> > a bootable disc. I booted with the CD and then the bootprogress
> > stopped here:
> > 
> > rootdev=0x0 rrootdev=0x300 rawdev=0x302
> > 
> > The bootprogress just stops without any errors. After some tries, it
> > works but some seconds later the whole process ends with an uvm fault.
> > I couldn't yet write down the fault because the machine reboots
> > immediately. DMESG is attached.
> > 
> > 
> > 
> 
> Sry, here the dmesg:

Could be a bad cd. Try a new one, or you can use bsd.rd. Copy it to the 
root of the hard disk, and boot it at the boot prompt. If the problem 
persists, try hooking up a serial console to catch details.

	-Otto

> 
> 
> -----
> OpenBSD 3.5 (GENERIC) #34: Mon Mar 29 12:24:55 MST 2004
>     deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
> cpu0: AMD Duron(tm) Processor ("AuthenticAMD" 686-class) 1.30 GHz
> cpu0:
> FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,
> FXSR,SSE
> real mem  = 234401792 (228908K)
> avail mem = 210989056 (206044K)
> using 2886 buffers containing 11821056 bytes (11544K) of memory
> mainbus0 (root)
> bios0 at mainbus0: AT/286+(00) BIOS, date 09/30/03, BIOS32 rev. 0 @
> 0xfdae0
> apm0 at bios0: Power Management spec V1.2
> apm0: AC on, no battery
> pcibios0 at bios0: rev. 2.1 @ 0xf0000/0x10000
> pcibios0: PCI IRQ Routing Table rev. 1.0 @ 0xf78e0/144 (7 entries)
> pcibios0: PCI Interrupt Router at 000:02:0 ("SIS 85C503 System" rev
> 0x00)
> pcibios0: PCI bus #1 is the last bus
> bios0: ROM list: 0xc0000/0xc000 0xcc000/0x8000!
> pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
> pchb0 at pci0 dev 0 function 0 "SIS 740 PCI" rev 0x01
> ppb0 at pci0 dev 1 function 0 "SIS 86C201 AGP" rev 0x00
> pci1 at ppb0 bus 1
> vga1 at pci1 dev 0 function 0 "SIS 650 VGA" rev 0x00: aperture at
> 0xc0000000, size 0x400000
> wsdisplay0 at vga1: console (80x25, vt100 emulation)
> wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
> pcib0 at pci0 dev 2 function 0 "SIS 85C503 System" rev 0x25
> pciide0 at pci0 dev 2 function 5 "SIS 5513 EIDE" rev 0x00: 740: DMA,
> channel 0 wired to compatibility, channel 1 wired to compatibility
> wd0 at pciide0 channel 0 drive 0: <ExcelStor Technology J340>
> wd0: 16-sector PIO, LBA48, 39266MB, 80418240 sectors
> wd1 at pciide0 channel 0 drive 1: <Maxtor 4D040H2>
> wd1: 16-sector PIO, LBA, 39083MB, 80043264 sectors
> wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
> wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 5
> atapiscsi0 at pciide0 channel 1 drive 0
> scsibus0 at atapiscsi0: 2 targets
> cd0 at scsibus0 targ 0 lun 0: <IDE, DVD-ROM 16X, 7.50> SCSI0 5/cdrom
> removable
> cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
> ohci0 at pci0 dev 3 function 0 "SIS 5597/5598 USB" rev 0x0f: irq 5,
> version 1.0, legacy support
> ohci0: SMM does not respond, resetting
> usb0 at ohci0: USB revision 1.0
> uhub0 at usb0
> uhub0: SIS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 3 ports with 3 removable, self powered
> ohci1 at pci0 dev 3 function 1 "SIS 5597/5598 USB" rev 0x0f: irq 5,
> version 1.0, legacy support
> ohci1: SMM does not respond, resetting
> usb1 at ohci1: USB revision 1.0
> uhub1 at usb1
> uhub1: SIS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub1: 3 ports with 3 removable, self powered
> "SIS 7002 USB" rev 0x00 at pci0 dev 3 function 3 not configured
> sis0 at pci0 dev 4 function 0 "SIS 900 10/100BaseTX" rev 0x90:  irq 11,
> address 00:0d:87:5a:60:d0
> ukphy0 at sis0 phy 1: Generic IEEE 802.3u media interface
> ukphy0: OUI 0x004063, model 0x0032, rev. 8
> cmpci0 at pci0 dev 9 function 0 "C-Media Electronics CMI8738/C3DX Audio"
> rev 0x10: irq 5
> audio0 at cmpci0
> rl0 at pci0 dev 11 function 0 "Realtek 8139" rev 0x10: irq 5 address
> 00:50:bf:e0:c5:40
> rlphy0 at rl0 phy 0: RTL internal phy
> isa0 at pcib0
> isadma0 at isa0
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard, using wsdisplay0
> pmsi0 at pckbc0 (aux slot)
> pckbc0: using irq 12 for aux slot
> wsmouse0 at pmsi0 mux 0
> pcppi0 at isa0 port 0x61
> midi0 at pcppi0: <PC speaker>
> sysbeep0 at pcppi0
> lpt0 at isa0 port 0x378/4 irq 7
> it0 at isa0 port 0x290/8: IT87
> npx0 at isa0 port 0xf0/16: using exception 16
> pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
> biomask c060 netmask c860 ttymask d8e2
> pctr: user-level cycle counter enabled
> mtrr: Pentium Pro MTRR support
> dkcsum: wd0 matched BIOS disk 80
> dkcsum: wd1 matched BIOS disk 81
> root on wd0a
> rootdev=0x0 rrootdev=0x300 rawdev=0x302
> umass0 at uhub0 port 2 configuration 1 interface 0
> umass0: Generic USB Storage Device, rev 1.10/1.00, addr 2
> umass0: using SCSI over Bulk-Only
> scsibus1 at umass0: 2 targets
> sd0 at scsibus1 targ 1 lun 0: <IC, USB Storage-CFC, 301b> SCSI0 0/direct
> removable
> sd0: drive offline
> sd1 at scsibus1 targ 1 lun 1: <IC, USB Storage-SMC, 301b> SCSI0 0/direct
> removable
> sd1: drive offline
> sd2 at scsibus1 targ 1 lun 2: <IC, USB Storage-MMC, 301b> SCSI0 0/direct
> removable
> sd2: drive offline
> sd3 at scsibus1 targ 1 lun 3: <IC, USB Storage-MSC, 301b> SCSI0 0/direct
> removable
> sd3: drive offline