Re: 3.6 snapshot from 08/27/04 hangs after boot

[Sascha Hanse <sensei@bsdberlin.org>]

On Wed, 1 Sep 2004 15:06:01 +0200 (CEST)
Otto Moerbeek <otto@drijf.net> wrote:

> 
> 
> On Wed, 1 Sep 2004, Sascha Hanse wrote:
> 
> > On Wed, 1 Sep 2004 14:28:11 +0200
> > Sascha Hanse <sensei@bsdberlin.org> wrote:
> > 
> > > Hi,
> > > 
> > > I wanted to upgrade my 3.5 Box to 3.6, so I used the cd36.iso to
> > > make a bootable disc. I booted with the CD and then the
> > > bootprogress stopped here:
> > > 
> > > rootdev=0x0 rrootdev=0x300 rawdev=0x302
> > > 
> > > The bootprogress just stops without any errors. After some tries,
> > > it works but some seconds later the whole process ends with an uvm
> > > fault. I couldn't yet write down the fault because the machine
> > > reboots immediately. DMESG is attached.
> > > 
> > > 
> > > 
> > 
> > Sry, here the dmesg:
> 
> Could be a bad cd. Try a new one, or you can use bsd.rd. Copy it to
> the root of the hard disk, and boot it at the boot prompt. If the
> problem persists, try hooking up a serial console to catch details.
> 
> 	-Otto
> 
I don't think it is a bad cd, I got the same error a week ago. And I'll
try the other stuff.

> > 
> > 
> > -----
> > OpenBSD 3.5 (GENERIC) #34: Mon Mar 29 12:24:55 MST 2004
> >     deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
> > cpu0: AMD Duron(tm) Processor ("AuthenticAMD" 686-class) 1.30 GHz
> > cpu0:
> > FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,
> > MMX, FXSR,SSE
> > real mem  = 234401792 (228908K)
> > avail mem = 210989056 (206044K)
> > using 2886 buffers containing 11821056 bytes (11544K) of memory
> > mainbus0 (root)
> > bios0 at mainbus0: AT/286+(00) BIOS, date 09/30/03, BIOS32 rev. 0 @
> > 0xfdae0
> > apm0 at bios0: Power Management spec V1.2
> > apm0: AC on, no battery
> > pcibios0 at bios0: rev. 2.1 @ 0xf0000/0x10000
> > pcibios0: PCI IRQ Routing Table rev. 1.0 @ 0xf78e0/144 (7 entries)
> > pcibios0: PCI Interrupt Router at 000:02:0 ("SIS 85C503 System" rev
> > 0x00)
> > pcibios0: PCI bus #1 is the last bus
> > bios0: ROM list: 0xc0000/0xc000 0xcc000/0x8000!
> > pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
> > pchb0 at pci0 dev 0 function 0 "SIS 740 PCI" rev 0x01
> > ppb0 at pci0 dev 1 function 0 "SIS 86C201 AGP" rev 0x00
> > pci1 at ppb0 bus 1
> > vga1 at pci1 dev 0 function 0 "SIS 650 VGA" rev 0x00: aperture at
> > 0xc0000000, size 0x400000
> > wsdisplay0 at vga1: console (80x25, vt100 emulation)
> > wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
> > pcib0 at pci0 dev 2 function 0 "SIS 85C503 System" rev 0x25
> > pciide0 at pci0 dev 2 function 5 "SIS 5513 EIDE" rev 0x00: 740: DMA,
> > channel 0 wired to compatibility, channel 1 wired to compatibility
> > wd0 at pciide0 channel 0 drive 0: <ExcelStor Technology J340>
> > wd0: 16-sector PIO, LBA48, 39266MB, 80418240 sectors
> > wd1 at pciide0 channel 0 drive 1: <Maxtor 4D040H2>
> > wd1: 16-sector PIO, LBA, 39083MB, 80043264 sectors
> > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
> > wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 5
> > atapiscsi0 at pciide0 channel 1 drive 0
> > scsibus0 at atapiscsi0: 2 targets
> > cd0 at scsibus0 targ 0 lun 0: <IDE, DVD-ROM 16X, 7.50> SCSI0 5/cdrom
> > removable
> > cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
> > ohci0 at pci0 dev 3 function 0 "SIS 5597/5598 USB" rev 0x0f: irq 5,
> > version 1.0, legacy support
> > ohci0: SMM does not respond, resetting
> > usb0 at ohci0: USB revision 1.0
> > uhub0 at usb0
> > uhub0: SIS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> > uhub0: 3 ports with 3 removable, self powered
> > ohci1 at pci0 dev 3 function 1 "SIS 5597/5598 USB" rev 0x0f: irq 5,
> > version 1.0, legacy support
> > ohci1: SMM does not respond, resetting
> > usb1 at ohci1: USB revision 1.0
> > uhub1 at usb1
> > uhub1: SIS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> > uhub1: 3 ports with 3 removable, self powered
> > "SIS 7002 USB" rev 0x00 at pci0 dev 3 function 3 not configured
> > sis0 at pci0 dev 4 function 0 "SIS 900 10/100BaseTX" rev 0x90:  irq
> > 11, address 00:0d:87:5a:60:d0
> > ukphy0 at sis0 phy 1: Generic IEEE 802.3u media interface
> > ukphy0: OUI 0x004063, model 0x0032, rev. 8
> > cmpci0 at pci0 dev 9 function 0 "C-Media Electronics CMI8738/C3DX
> > Audio" rev 0x10: irq 5
> > audio0 at cmpci0
> > rl0 at pci0 dev 11 function 0 "Realtek 8139" rev 0x10: irq 5 address
> > 00:50:bf:e0:c5:40
> > rlphy0 at rl0 phy 0: RTL internal phy
> > isa0 at pcib0
> > isadma0 at isa0
> > pckbc0 at isa0 port 0x60/5
> > pckbd0 at pckbc0 (kbd slot)
> > pckbc0: using irq 1 for kbd slot
> > wskbd0 at pckbd0: console keyboard, using wsdisplay0
> > pmsi0 at pckbc0 (aux slot)
> > pckbc0: using irq 12 for aux slot
> > wsmouse0 at pmsi0 mux 0
> > pcppi0 at isa0 port 0x61
> > midi0 at pcppi0: <PC speaker>
> > sysbeep0 at pcppi0
> > lpt0 at isa0 port 0x378/4 irq 7
> > it0 at isa0 port 0x290/8: IT87
> > npx0 at isa0 port 0xf0/16: using exception 16
> > pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> > fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
> > biomask c060 netmask c860 ttymask d8e2
> > pctr: user-level cycle counter enabled
> > mtrr: Pentium Pro MTRR support
> > dkcsum: wd0 matched BIOS disk 80
> > dkcsum: wd1 matched BIOS disk 81
> > root on wd0a
> > rootdev=0x0 rrootdev=0x300 rawdev=0x302
> > umass0 at uhub0 port 2 configuration 1 interface 0
> > umass0: Generic USB Storage Device, rev 1.10/1.00, addr 2
> > umass0: using SCSI over Bulk-Only
> > scsibus1 at umass0: 2 targets
> > sd0 at scsibus1 targ 1 lun 0: <IC, USB Storage-CFC, 301b> SCSI0
> > 0/direct removable
> > sd0: drive offline
> > sd1 at scsibus1 targ 1 lun 1: <IC, USB Storage-SMC, 301b> SCSI0
> > 0/direct removable
> > sd1: drive offline
> > sd2 at scsibus1 targ 1 lun 2: <IC, USB Storage-MMC, 301b> SCSI0
> > 0/direct removable
> > sd2: drive offline
> > sd3 at scsibus1 targ 1 lun 3: <IC, USB Storage-MSC, 301b> SCSI0
> > 0/direct removable
> > sd3: drive offline