[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
wd error on macppc

To: tech@openbsd.org
Subject: wd error on macppc
From: itojun@iijlab.net
Date: Fri, 06 Jun 2003 13:58:17 +0900
	i get a lot of device timeouts with recent kernel (macppc, iBook 2002
	summer).  sector number varies time to time.  machine locks up
	while showing those errors.  any clues?

itojun



on, 400 dpi
wsmouse0 at ams0 mux 0
abtn0 at adb0 addr 7: brightness/volume/eject buttons
apm0 at adb0: battery flags 0x5, 94% charged
wdc0 at macobio0 irq 19: DMA transfer
wd0 at wdc0 channel 0 drive 0: <IC25N040ATCS04-0>
wd0: 16-sector PIO, LBA, 38154MB, 16383 cyl, 16 head, 63 sec, 78140160 sectors
atapiscsi0 at wdc0 channel 0 drive 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TOSHIBA, DVD-ROM SD-R2102, 1K27> SCSI0 5/cdrom removable
wd0(wdc0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2
cd0(wdc0:0:1): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2
wi0 at macobio0 irq 57:
wi0: Firmware 8.12 variant 1, address 00:30:65:15:6c:10
ohci0 at pci1 dev 24 function 0 "Apple Pangea USB" rev 0x00: irq 27, OHCI version 1.0
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x0000 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ohci1 at pci1 dev 25 function 0 "Apple Pangea USB" rev 0x00: irq 28, OHCI version 1.0
usb1 at ohci1: USB revision 1.0
uhub1 at usb1
uhub1: vendor 0x0000 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
mpcpcibr2 at mainbus0: uni-north, Revision 0xff
pci2 at mpcpcibr2 bus 0
pchb2 at pci2 dev 11 function 0 "Apple Pangea Host-PCI" rev 0x00
fwohci0 at pci2 dev 14 function 0 "Apple Pangea FireWire" rev 0x00: irq 40
fwohci0: OHCI 1.0, 00:03:93:ff:fe:a6:05:c2, 400Mb/s, 2048 max_rec, 8 iso_ctx
gem0 at pci2 dev 15 function 0 "Apple GMAC" rev 0x00
gem0: address 00:03:93:a6:05:c2
bmtphy0 at gem0 phy 0: BCM5221 100baseTX PHY, rev. 4
gem0: using irq 41 for interrupt
bootpath: '/pci@f2000000/mac-io@17/ata-4@1f000/disk@0/bsd'
boot device: wd0.
root on wd0a
rootdev=0x0 rrootdev=0xb00 rawdev=0xb02
WARNING: / was not properly unmounted
WARNING: clock gained 3 days -- CHECK AND RESET THE DATE!
fw0 at fwohci0: 00:03:93:ff:fe:a6:05:c2:0a:02:20:00:00:00:00:00
ugen0 at uhub1 port 2
ugen0: HCF USB V.90 Data/Fax Modem Apple internal modem, rev 1.10/1.00, addr 2
wd0(wdc0:0:0): timeout
	type: ata
	c_bcount: 8192
	c_skip: 0
wdc0 channel 0: reset failed for drive 0
wd0g: device timeout writing fsbn 42610480 of 42610480-42610495 (wd0 bn 61172544; cn 60687 tn 0 sn 48), retrying
wdc0:0:0: not ready, st=0x80, err=0x00
wd0g: device timeout writing fsbn 42610480 of 42610480-42610495 (wd0 bn 61172544; cn 60687 tn 0 sn 48), retrying
wd0: soft error (corrected)
wd0(wdc0:0:0): timeout
	type: ata
	c_bcount: 8192
	c_skip: 0
wdc0 channel 0: reset failed for drive 0
wd0g: device timeout reading fsbn 34490400 of 34490400-34490415 (wd0 bn 53052464; cn 52631 tn 6 sn 38), retrying
wdc0:0:0: not ready, st=0x80, err=0x00
wdc0 channel 0: reset failed for drive 0
wd0g: device timeout reading fsbn 34490400 of 34490400-34490415 (wd0 bn 53052464; cn 52631 tn 6 sn 38), retrying
wdc0:0:0: not ready, st=0x80, err=0x00
wdc0 channel 0: reset failed for drive 0
wd0g: device timeout reading fsbn 34490400 of 34490400-34490415 (wd0 bn 53052464; cn 52631 tn 6 sn 38), retrying
wdc0:0:0: not ready, st=0x80, err=0x00
wdc0 channel 0: reset failed for drive 0
wd0g: device timeout reading fsbn 34490400 of 34490400-34490415 (wd0 bn 53052464; cn 52631 tn 6 sn 38), retrying
wdc0:0:0: not ready, st=0x80, err=0x00
wdc0 channel 0: reset failed for drive 0
wd0g: device timeout reading fsbn 34490400 of 34490400-34490415 (wd0 bn 53052464; cn 52631 tn 6 sn 38), retrying
wdc0:0:0: not ready, st=0x80, err=0x00
wdc0 channel 0: reset failed for drive 0
wd0g: device timeout reading fsbn 34490400 of 34490400-34490415 (wd0 bn 53052464; cn 52631 tn 6 sn 38)
wdc0:0:0: not ready, st=0x80, err=0x00
wdc0 channel 0: reset failed for drive 0
wd0g: device timeout writing fsbn 544 of 544-559 (wd0 bn 18562608; cn 18415 tn 4 sn 36), retrying
wd0: soft error (corrected)
syncing disks... done
rebooting

[ using 255448 bytes of bsd ELF symbol table ]
console out [ATY,Fall_A]console in [keyboard] ADB found
using parent ATY,FallParent:: memaddr 98000000 size 8000000, : consaddr 9c008000, : ioaddr 90020000, size 20000: memtag 8000, iotag 8000: width 1024 linebytes 1024 height 768 depth 8
Copyright (c) 1982, 1986, 1989, 1991, 1993
	The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2003 OpenBSD. All rights reserved.  http://www.OpenBSD.org

OpenBSD 3.3-current (GENERIC) #72: Fri Jun  6 12:10:00 JST 2003
    itojun@tapioca.itojun.org:/home/itojun/OpenBSD/src/sys/arch/macppc/compile/GENERIC
real mem = 671088640 (655360K)
avail mem = 604569600 (590400K)
using 1254 buffers containing 33554432 bytes of memory
mainbus0 (root)
cpu0 at mainbus0: 750FX (Revision 112): 700 MHz: 512KB L2 cache
memc0 at mainbus0: uni-n
mpcpcibr0 at mainbus0: uni-north, Revision 0xff
pci0 at mpcpcibr0 bus 0
pchb0 at pci0 dev 11 function 0 "Apple Pangea AGP" rev 0x00
vgafb0 at pci0 dev 16 function 0 "ATI Radeon Mobility M6 LY" rev 0x00, mmio
wsdisplay0 at vgafb0: console (std, vt100 emulation)
mpcpcibr1 at mainbus0: uni-north, Revision 0x0
pci1 at mpcpcibr1 bus 0
pchb1 at pci1 dev 11 function 0 "Apple Pangea Host-PCI" rev 0x00
macobio0 at pci1 dev 23 function 0 "Apple Pangea" rev 0x00
openpic0 at macobio0: version 0x4614
gpio_obio0 at macobio0
gpio_obio1 at gpio_obio0 offset 0x59 irq 47
programmer-switch at gpio_obio0 offset 0x61 not configured
firewire-linkon at gpio_obio0 offset 0x5b not configured
cpu-vcore-select at gpio_obio0 offset 0x6b not configured
extint-gpio4 at gpio_obio0 offset 0x5c not configured
gpio9 at gpio_obio0 offset 0x73 not configured
extint-gpio12 at gpio_obio0 offset 0x64 not configured
zsc0 at macobio0: irq 22,23
zstty0 at zsc0 channel 0
zstty1 at zsc0 channel 1
adb0 at macobio0 irq 25: via-pmu 3 targets
aed0 at adb0 addr 0: ADB Event device
akbd0 at adb0 addr 2: PowerBook G4 keyboard (Inverted T)
wskbd0 at akbd0 (mux 1 ignored for console): console keyboard, using wsdisplay0
ams0 at adb0 addr 3: EMP trackpad <tpad> 2-button, 400 dpi
wsmouse0 at ams0 mux 0
abtn0 at adb0 addr 7: brightness/volume/eject buttons
apm0 at adb0: battery flags 0x5, 94% charged
wdc0 at macobio0 irq 19: DMA transfer
wd0 at wdc0 channel 0 drive 0: <IC25N040ATCS04-0>
wd0: 16-sector PIO, LBA, 38154MB, 16383 cyl, 16 head, 63 sec, 78140160 sectors
atapiscsi0 at wdc0 channel 0 drive 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TOSHIBA, DVD-ROM SD-R2102, 1K27> SCSI0 5/cdrom removable
wd0(wdc0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2
cd0(wdc0:0:1): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2
wi0 at macobio0 irq 57:
wi0: Firmware 8.12 variant 1, address 00:30:65:15:6c:10
ohci0 at pci1 dev 24 function 0 "Apple Pangea USB" rev 0x00: irq 27, OHCI version 1.0
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x0000 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ohci1 at pci1 dev 25 function 0 "Apple Pangea USB" rev 0x00: irq 28, OHCI version 1.0
usb1 at ohci1: USB revision 1.0
uhub1 at usb1
uhub1: vendor 0x0000 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
mpcpcibr2 at mainbus0: uni-north, Revision 0xff
pci2 at mpcpcibr2 bus 0
pchb2 at pci2 dev 11 function 0 "Apple Pangea Host-PCI" rev 0x00
fwohci0 at pci2 dev 14 function 0 "Apple Pangea FireWire" rev 0x00: irq 40
fwohci0: OHCI 1.0, 00:03:93:ff:fe:a6:05:c2, 400Mb/s, 2048 max_rec, 8 iso_ctx
gem0 at pci2 dev 15 function 0 "Apple GMAC" rev 0x00
gem0: address 00:03:93:a6:05:c2
bmtphy0 at gem0 phy 0: BCM5221 100baseTX PHY, rev. 4
gem0: using irq 41 for interrupt
bootpath: '/pci@f2000000/mac-io@17/ata-4@1f000/disk@0/bsd'
boot device: wd0.
root on wd0a
rootdev=0x0 rrootdev=0xb00 rawdev=0xb02
fw0 at fwohci0: 00:03:93:ff:fe:a6:05:c2:0a:02:20:00:00:00:00:00
ugen0 at uhub1 port 2
ugen0: HCF USB V.90 Data/Fax Modem Apple internal modem, rev 1.10/1.00, addr 2
wdc0:0:0: not ready, st=0x80, err=0x00
wdc0 channel 0: reset failed for drive 0
wd0e: device timeout writing fsbn 1306496 of 1306496-1306511 (wd0 bn 5405520; cn 5362 tn 9 sn 57), retrying
wdc0:0:0: not ready, st=0x80, err=0x00
wd0e: device timeout writing fsbn 1306496 of 1306496-1306511 (wd0 bn 5405520; cn 5362 tn 9 sn 57), retrying
wd0: soft error (corrected)
wd0(wdc0:0:0): timeout
	type: ata
	c_bcount: 1024
	c_skip: 0
Follow-Ups:
- Re: wd error on macppc
  - From: Alexander Yurchenko <grange@rt.mipt.ru>
- Re: wd error on macppc
  - From: itojun@iijlab.net
Prev by Date: Re: wi0 oddity
Next by Date: Re: wd error on macppc
Prev by thread: You sent a message with an executable attached.
Next by thread: Re: wd error on macppc
Index(es):
- Date
- Thread