Re: xl driver messages

[Ian Darwin <ian@darwinsys.com>]

On Thu, Oct 21, 1999 at 12:00:50PM -0700, Chris Cappuccio wrote:
> This happens because you are using a custom kernel
> 
> Before you report errors, try GENERIC
> 
> You will find that xl has been converted to use mii drivers,
> 
> and so you need exphy* at mii ? phy ?
> 
> in your config

Good point. HOWEVER, the machine that IS running generic still gives 
the "overrun error".

Ian

OpenBSD 2.6 (GENERIC) #674: Sun Oct 17 19:52:29 MDT 1999
    deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: xchg bug workaround performed
cpu0: Cyrix 6x86 (486-class)
BIOS mem  = 654336 conventional, 32505856 extended
real mem  = 33161216
avail mem = 26640384
using 430 buffers containing 1761280 bytes of memory
mainbus0 (root)
bios at mainbus0 not configured
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82439HX (Triton II) TXC Host" rev 0x03
pcib0 at pci0 dev 7 function 0 "Intel 82371SB (Triton II) PCI-ISA" rev 0x01
pciide0 at pci0 dev 7 function 1 "Intel 82371SB (Triton II) IDE" rev 0x00: DMA, channel 0 wired to compatibility, channel 1 wired to compatibility
xl0 at pci0 dev 17 function 0 "3Com 3c905 100Base-TX" rev 0x00: irq 10 address 00:60:97:d1:55:96
nsphy0 at xl0 phy 24: DP83840 10/100 media interface, rev. 1
ahc1 at pci0 dev 19 function 0 "Adaptec AHA-2940U" rev 0x00: irq 10
ahc1: aic7880 Single Channel, SCSI Id=7, 16 SCBs
scsibus0 at ahc1: 8 targets
ahc1: target 0 synchronous at 10.0MHz, offset = 0xf
sd0 at scsibus0 targ 0 lun 0: <DEC, RZ74     (C) DEC, 427N> SCSI2 0/direct fixed
sd0: 3406MB, 3055 cyl, 25 head, 91 sec, 512 bytes/sec, 6976375 sec total
ahc1: target 1 synchronous at 10.0MHz, offset = 0xf
sd1 at scsibus0 targ 1 lun 0: <Quantum, XP31070W, L912> SCSI2 0/direct fixed
sd1: 1075MB, 3907 cyl, 5 head, 112 sec, 512 bytes/sec, 2203480 sec total
ahc1: target 4 synchronous at 5.0MHz, offset = 0xf
st0 at scsibus0 targ 4 lun 0: <WangDAT, Model 1300XL, 02.5> SCSI2 1/sequential removable
st0: drive empty
probe(ahc1:5:0): Target Busy
probe(ahc1:5:0): Target Busy
cd0 at scsibus0 targ 5 lun 0: <IMS, CDD2000/00, 1.26> SCSI2 5/cdrom removable
"ATI Technologies Mach64 GT" rev 0x48 at pci0 dev 20 function 0 not configured
isa0 at pcib0
isadma0 at isa0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
vt0 at isa0 port 0x60/16 irq 1: generic VGA, 80 col, color, 8 scr, mf2-kbd
pms0 at vt0 irq 12
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
biomask 440 netmask 440 ttymask 14c2
pctr: no performance counters in CPU
root on sd0a
rootdev=0x400 rrootdev=0xd00 rawdev=0xd02
IP Filter: initialized.  Default = pass all, Logging = enabled
xl0: transmission error: 90
xl0: tx underrun, increasing tx start threshold to 120