[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: URGENT: ATAPI testing needed for 2.6
[sorry for the long mail]
Information and question:
I was one of those who complained about the non-detection of ATAPI CDROM.
With the new code, it is detected but not to be mounted. O.w. the system
works fine.
Since it was a working system (under OBSD2.5/NetBSD) should I still tweak
with the jumper settings? I have very little knowledge of these things, so
would prefer not to, unless someone tells me what to do.
The floppy26.fs as well as the system is from Oct28 snapshot.
Thanks,
Gangadhar.
Here is the dmesg.boot (the first few lines were flushed out):
===============
ppb0 at pci0 dev 1 function 0 "Intel 82443BX AGP (PAC)" rev 0x02
pci1 at ppb0 bus 1
pcib0 at pci0 dev 7 function 0 "Intel 82371AB PIIX4 ISA" rev 0x02
pciide0 at pci0 dev 7 function 1 "Intel 82371AB IDE (PIIX4)" rev 0x01: DMA, chan
nel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <ST36531A>
wd0: can use 32-bit, PIO mode 4, DMA mode 2, Ultra-DMA mode 2
wd0: 32-sector PIO, LBA, 6204MB, 13446 cyl, 15 head, 63 sec, 12706470 sectors
pciide0: channel 0 interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (using DMA data transfers)
atapiscsi0 at pciide0 channel 1
scsibus0 at atapiscsi0: 2 targets
wdc_atapi_done: sc_xfer->error 4
atapiscsi0: transfer error, downgrading to PIO mode 4
atapiscsi0(pciide0:1:0): using PIO mode 4
wdc_atapi_done: sc_xfer->error 4
[
[snip:
[snip: the above message was repeated 49 times
[snip:
[
cd0 at scsibus0 targ 0 lun 0: <CREATIVE, CD3621E ZC100, 1.00> SCSI0 5/cdrom rem
ovable
cd0: can use 32-bit, PIO mode 4
pciide0: channel 1 interrupting at irq 15
cd0(pciide0:1:0): using PIO mode 4
"Intel 82371AB USB (PIIX4)" rev 0x01 at pci0 dev 7 function 2 not configured
"Intel 82371AB Power Management (PIIX4)" rev 0x02 at pci0 dev 7 function 3 not c
onfigured
"S3 ViRGE DX/GX" rev 0x01 at pci0 dev 15 function 0 not configured
de0 at pci0 dev 16 function 0 "DEC DECchip 21142/3" rev 0x30: irq 9
de0: 21143 [10-100Mb/s] pass 3.0 address 00:48:54:00:a5:2d
isa0 at pcib0
isadma0 at isa0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
vt0 at isa0 port 0x60/16 irq 1: unknown S3, 80 col, color, 8 scr, mf2-kbd
pms0 at vt0 irq 12
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
isapnp0 at isa0 port 0x279: read port 0x203
sb1 at isapnp0 "Creative ViBRA16X PnP, CTL0043, , Audio" port 0x220/16,0x330/2,0
x388/4 irq 5 drq 1,3: dsp v4.16
midi1 at sb1: <SB MPU-401 UART>
audio0 at sb1
opl0 at sb1: model OPL3
midi2 at opl0: <SB Yamaha OPL3>
joy0 at isapnp0 "Creative ViBRA16X PnP, CTL7005, PNPB02F, Game" port 0x201/1
biomask c040 netmask c240 ttymask d2c2
pctr: 686-class user-level performance counters enabled
dkcsum: wd0 matched BIOS disk 80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
de0: enabling 10baseT port
--
I am working today; do not want to go anywhere.
NANDYALA D. Gangadhar, EE, IISc., Bangalore 560 012.