Re: Oct 29 i386 snapshot == atapiscsi problems

[kwesterback@home.com]

The problem seems to have been eradicated in Oct 31 snapshot.

I (U)pgraded and rebooted many times with no CD in the 
drive with no recurrance of the problem.

Great work! Thanks.

.... Ken

On Sun, Oct 31, 1999 at 05:26:32AM -0500, kwesterback@home.com wrote:
> Executive Summary:
> 
> Oct 29 i386 floppy26.fs install floppy boot displayed
> atapiscsi error on first boot, subsequent reboots did
> not display same message. (U)pgrade worked but could not
> boot from wd0. fd0/wd0 boots display same error until
> a CD placed in drive, and then both boot OK. Take CD
> out and no boot.
> 
 
/var/run/dmesg.boot from former problem machine:

OpenBSD 2.6 (GENERIC) #694: Sun Oct 31 21:08:41 MST 1999
    deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: AMD K6-2 ("AuthenticAMD" 586-class) 351 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,MMX
BIOS mem  = 654336 conventional, 32440320 extended
real mem  = 33095680
avail mem = 26578944
using 429 buffers containing 1757184 bytes of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(52) BIOS, date 06/09/99
bios0: diskinfo 0xe055800c cksumlen 1 memmap 0xe0558088 apminfo 0xe0558134
apm0 at bios0: Power Management spec V1.1
apm0: AC on, no battery
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "VIA VT82C597 (Apollo VP3) Host-PCI" rev 0x04
ppb0 at pci0 dev 1 function 0 "VIA VT82C598 (Apollo MVP3) PCI-AGP" rev 0x00
pci1 at ppb0 bus 1
pcib0 at pci0 dev 7 function 0 "VIA VT82C586 (Apollo VP) PCI-ISA" rev 0x41
pciide0 at pci0 dev 7 function 1 "VIA VT82C586A IDE" rev 0x06: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <QUANTUM FIREBALL EX3.2A>
wd0: can use 32-bit, PIO mode 4, DMA mode 2, Ultra-DMA mode 2
wd0: 16-sector PIO, LBA, 3079MB, 6256 cyl, 16 head, 63 sec, 6306048 sectors
pciide0: channel 0 interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (using DMA data transfers)
atapiscsi0 at pciide0 channel 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <ATAPI, CD-ROM DRIVE-40X, T0CP> SCSI0 5/cdrom removable
cd0: can use 32-bit, PIO mode 3, DMA mode 2, Ultra-DMA mode 2
pciide0: channel 1 interrupting at irq 15
cd0(pciide0:1:0): using PIO mode 3, Ultra-DMA mode 2 (using DMA data transfers)
ppb1 at pci0 dev 7 function 3 "VIA VT82C586 (Apollo VP) Power Management" rev 0x10
ppb1: not configured by system firmware
"ATI Technologies Mach64 GX" rev 0x01 at pci0 dev 8 function 0 not configured
xl0 at pci0 dev 9 function 0 "3Com 3c905 100Base-TX" rev 0x00: irq 10 address 00:60:08:bf:e3:6d
nsphy0 at xl0 phy 24: DP83840 10/100 media interface, rev. 1
isa0 at pcib0
isadma0 at isa0
ep0 at isa0 port 0x300/16 irq 5: address 00:20:af:9c:30:66, utp/aui/bnc (default utp)
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0/16: using exception 16
vt0 at isa0 port 0x60/16 irq 1: generic VGA, 80 col, color, 8 scr, mf2-kbd
pms0 at vt0 irq 12
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask c040 netmask c460 ttymask d462
pctr: user-level cycle counter enabled
dkcsum: wd0 matched BIOS disk 80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
IP Filter: initialized.  Default = pass all, Logging = enabled
xl0: transmission error: 90
xl0: tx underrun, increasing tx start threshold to 120