Configuring my internal modem (in Toshiba Satellite Laptop)

[Rick Pettit <rpettit@vailsys.com>]

	I have also sent my dmesg output to dmesg@openbsd.org, but figured
I would send it here and ask about my modem specifically.  I cannot get my
internal modem configured.  I don't even know if it is supported.  Below
is my dmesg output:

pcic0 controller 0 socket 1
ep1 at pcmcia1 function 0 "3Com Corporation, 3C589D, TP/BNC LAN Card Ver.
2a" port 0x360/16 irq 10: address 00:60:97:92:2b:e8, utp/aui/bnc (default
utp)
pcic0: irq 9
biomask c040 netmask c460 ttymask d6e2
pctr: 686-class user-level performance counters enabled
dkcsum: wd0 matched BIOS disk 80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
ne3: device timeout
syncing disks... done
rebooting...
OpenBSD 2.6-beta (GENERIC) #661: Thu Oct  7 22:52:37 MDT 1999
    deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium II (Celeron) ("GenuineIntel" 686-class, 128KB L2
cache) 300 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SYS,MTRR,PGE,MCA,CMOV,PAT,PSE36,SER,MMX,FXSR
BIOS mem  = 654336 conventional, 65929216 extended
real mem  = 66584576
avail mem = 57847808
using 838 buffers containing 3432448 bytes of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(63) BIOS, date 01/12/99
bios0: diskinfo 0xe055800c cksumlen 1 memmap 0xe0558088 apminfo 0xe0558184
apm0 at bios0: Power Management spec V1.1
apm0: battery life expectancy 100%
apm0: AC on, battery charge high, estimated 2:30 minutes
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82443BX Host-PCI (no AGP)" rev 0x03
"Toshiba (2nd ID) ToPIC97 PCI-CardBus" rev 0x05 at pci0 dev 2 function 0
not configured
"Toshiba (2nd ID) ToPIC97 PCI-CardBus" rev 0x05 at pci0 dev 2 function 1
not configured
vendor "Trident", unknown product 0x9525 (class display, subclass VGA, rev
0x49) at pci0 dev 4 function 0 not configured
pcib0 at pci0 dev 5 function 0 "Intel 82371AB PIIX4 ISA" rev 0x02
pciide0 at pci0 dev 5 function 1 "Intel 82371AB IDE (PIIX4)" rev 0x01:
DMA, channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <IBM-DKLA-24320>
wd0: 16-sector PIO, LBA, 4126MB, 8944 cyl, 15 head, 63 sec, 8452080
sectors
wd0: 32-bit, supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2
pciide0: channel 0 interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (using DMA data
transfers)
atapiscsi0 at pciide0 channel 1
atapiscsi0: 32-bit, supports PIO mode 4, DMA mode 2
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TOSHIBA, CD-ROM XM-1802D, 1d21> SCSI0
5/cdrom removable
pciide0: channel 1 interrupting at irq 15
atapiscsi0(pciide0:1:0): using PIO mode 4, DMA mode 2 (using DMA data
transfers)
"Intel 82371AB USB (PIIX4)" rev 0x01 at pci0 dev 5 function 2 not
configured
"Intel 82371AB Power Management (PIIX4)" rev 0x02 at pci0 dev 5 function 3
not configured
vendor "AT&T/Lucent", unknown product 0x441 (class communications,
subclass miscellaneous, rev 0x01) at pci0 dev 7 function 0 not configured
"Toshiba (2nd ID) Fast Infrared Type O" rev 0x23 at pci0 dev 10 function 0
not configured
"ESS Maestro 2E" rev 0x10 at pci0 dev 12 function 0 not configured
isa0 at pcib0
isadma0 at isa0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns8250, no fifo
vt0 at isa0 port 0x60/16 irq 1: TVGA 9750 (3DImage), 80 col, color, 8 scr,
mf2-kbd
pms0 at vt0 irq 12
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
pcic0 at isa0 port 0x3e0/2 iomem 0xd0000/16384
pcic0 controller 0: <Intel 82365SL rev 1> has sockets A and B
pcmcia0 at pcic0 controller 0 socket 0
ne3 at pcmcia0 function 0 "Linksys, EtherFast 10/100 PC Card (PCMPC100), "
port 0x340/16 irq 5
ne3: address 00:e0:98:08:d8:c9
pcmcia1 at pcic0 controller 0 socket 1
ep1 at pcmcia1 function 0 "3Com Corporation, 3C589D, TP/BNC LAN Card Ver.
2a" port 0x360/16 irq 10: address 00:60:97:92:2b:e8, utp/aui/bnc (default
utp)
pcic0: irq 9
biomask c040 netmask c460 ttymask d6e2
pctr: 686-class user-level performance counters enabled
dkcsum: wd0 matched BIOS disk 80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302


	I would be *very* appreciative if anyone could help me get this
modem working.  Also, if you have time and feel like helping a guy out,
you could explain to me how to get some of the other non-configured
hardware up and doing its thing.  Thanks a lot, and keep up the good work
guys.


							- Rick Pettit