...install problem with OpenBSD 2.8...

[Next <next_(_at_)_nextonline_(_dot_)_org>]

Hi,
I use  2.7 generic kernel with no problems on an L440Gx+ Intel server
board with a tnt2 pci card
When I install 2.8, i have many blinking asci pacman and symbols on my
screen and the boot sequence crashes.
If I remove the tnt2 card, it works fine. (but i need it ;o)

i saw the update of the faq about this, but i have not found any manner
to disable pcibios in my bios.

here is a copy of my dmesg:

X-----------------------------------------------X

OpenBSD 2.7 (GENERIC) #25: Sat May 13 18:04:26 MDT 2000
    deraadt_(_at_)_i386_(_dot_)_openbsd_(_dot_)_org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium III (Coppermine) ("GenuineIntel" 686-class) 697 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SYS,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SIMD

real mem  = 267956224 (261676K)
avail mem = 243879936 (238164K)
using 3296 buffers containing 13500416 bytes (13184K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(a7) BIOS, date 06/06/00
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82440BX PCI-AGP (PAC)" rev 0x00
ppb0 at pci0 dev 1 function 0 "Intel 82440BX AGP (PAC)" rev 0x00
pci1 at ppb0 bus 1
ppb1 at pci1 dev 15 function 0 "DEC DECchip 21150-BC PCI-PCI" rev 0x06
pci2 at ppb1 bus 2
rl0 at pci2 dev 4 function 0 "Realtek 8139" rev 0x10: irq 11 address
00:10:a7:02:f7:9b
rlphy0 at rl0 phy 0: RTL internal phy
rl1 at pci2 dev 7 function 0 "Realtek 8139" rev 0x10: irq 5 address
00:10:a7:02:f6:24
rlphy1 at rl1 phy 0: RTL internal phy
vendor "Nvidia", unknown product 0x2c (class display, subclass VGA, rev
0x15) at pci0 dev 9 function 0 not configured
ahc1 at pci0 dev 11 function 0 "Adaptec AIC-7850" rev 0x03: irq 11
ahc1: Single Channel A, SCSI Id=7, 3/255 SCBs
ahc1: Host Adapter Bios disabled.  Using default SCSI device parameters
scsibus0 at ahc1: 8 targets
ahc1: target 4 synchronous at 10.0MHz, offset = 0xf
cd0 at scsibus0 targ 4 lun 0: <PLEXTOR, CD-ROM PX-32TS, 1.03> SCSI2
5/cdrom removable
ahc2 at pci0 dev 12 function 0 "Adaptec(2) AIC-7896/7 Ultra2" rev 0x00:
irq 11
ahc2: Wide Channel A, SCSI Id=7, 16/255 SCBs
scsibus1 at ahc2: 16 targets
ahc3 at pci0 dev 12 function 1 "Adaptec(2) AIC-7896/7 Ultra2" rev 0x00:
irq 11
ahc3: Wide Channel B, SCSI Id=7, 16/255 SCBs
scsibus2 at ahc3: 16 targets
eap0 at pci0 dev 13 function 0 "Ensoniq AudioPCI97" rev 0x08: irq 11
ac97: codec id 0x83847609 (SigmaTel STAC9721)
ac97: codec features 18 bit DAC, 18 bit ADC, Rockwell 3D
audio0 at eap0
fxp0 at pci0 dev 14 function 0 "Intel 82557" rev 0x08: irq 10, address
00:d0:b7:a7:b1:f9
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
pcib0 at pci0 dev 18 function 0 "Intel 82371AB PIIX4 ISA" rev 0x02
pciide0 at pci0 dev 18 function 1 "Intel 82371AB IDE (PIIX4)" rev 0x01:
DMA, channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <IBM-DPTA-351500>
wd0: can use 32-bit, PIO mode 4, DMA mode 2, Ultra-DMA mode 2
wd0: 16-sector PIO, LBA, 14324MB, 16383 cyl, 16 head, 63 sec, 29336832
sectors
pciide0: channel 0 interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (using DMA data
transfers)
"Intel 82371AB USB (PIIX4)" rev 0x01 at pci0 dev 18 function 2 not
configured
"Intel 82371AB Power Management (PIIX4)" rev 0x02 at pci0 dev 18
function 3 not configured
"Cirrus Logic CL-GD5480" rev 0x23 at pci0 dev 20 function 0 not
configured
isa0 at pcib0
isadma0 at isa0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
vt0 at isa0 port 0x60/16 irq 1: vga 80 col, color, 8 scr, mf2-kbd
pms0 at vt0 irq 12
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask 4840 netmask 4c60 ttymask 5ce2
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: wd0 matched BIOS disk 80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302

X------------------------------------------------------X

that's all. i hope it could help you to solve the problem.

ps: thanks for this great system

        Next

"...Choose your drug, choose OpenBSD..."