Prism 2.5 HostAP + WEP not working....

[matt snow <mattsnow_(_at_)_gmail_(_dot_)_com>]

Sorry if this has already been covered but I have not been able to
find anything solid on this topic.
please forgive me if this is the wrong list, let me know if this is
not the correct list, and I will resend to the appropriet list.

I have an OpenBSD 3.6 box with the following hardware:
* AMD K6 333MHz CPU 
* 128MB RAM, 6GB Fujitsu hard drive
* Intel 82557 dual port 10/100Mbps NIC
* Netgear MA311 802.11b PCI adapter (Prism 2.5)
* Hawking 6dBi omni-directional antenna

fxp0 has a external IP 66.x.x.x, fxp1 has an IP of 172.16.1.254 and is
bridged with wi0.
wi0 is configured for HostAP mode, clients can connect to the SSID, IP
traffic passes through
without any problems.
Once I enable wep either by command line or editing /etc/hostname.wi0
and adding -e 1 -k passs
The WiFi client can still connect to the access point after
reconfiguring for WEP, but no IP traffic is passed.
running brconfig bridge0 shows the MAC address of the laptop clients
wifi card, and the wired ethernet clients.

So my question is: does the wi driver support WEP in HostAP mode?

Here is the dmesg:
(drama_(_at_)_obf) ~ > dmesg
OpenBSD 3.6 (GENERIC) #59: Fri Sep 17 12:32:57 MDT 2004
    deraadt_(_at_)_i386_(_dot_)_openbsd_(_dot_)_org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: AMD-K6(tm) 3D processor ("AuthenticAMD" 586-class) 343 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,PGE,MMX
real mem  = 129605632 (126568K)
avail mem = 111579136 (108964K)
using 1607 buffers containing 6582272 bytes (6428K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(17) BIOS, date 05/07/99, BIOS32 rev. 0 @ 0xfb310
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xb7ac
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdc00/128 (6 entries)
pcibios0: PCI Exclusive IRQs: 5 7 10 11
pcibios0: PCI Interrupt Router at 000:01:0 ("SIS 85C503 System" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0xc000 0xcc000/0x2000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "SIS 5597 Host" rev 0x10
pcib0 at pci0 dev 1 function 0 "SIS 85C503 System" rev 0x01
pciide0 at pci0 dev 1 function 1 "SIS 5513 EIDE" rev 0xd0: 5597/5598:
DMA, channel 0 configured to compatibility, channel 1 configured to
compatibility
wd0 at pciide0 channel 0 drive 0: <FUJITSU MPE3064AT>
wd0: 16-sector PIO, LBA, 6187MB, 12672450 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
ohci0 at pci0 dev 1 function 2 "SIS 5597/5598 USB" rev 0x10: irq 7,
version 1.0, legacy support
ohci0: SMM does not respond, resetting
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: SIS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ppb0 at pci0 dev 15 function 0 "DEC 21152 PCI-PCI" rev 0x03
pci1 at ppb0 bus 1
fxp0 at pci1 dev 4 function 0 "Intel 82557" rev 0x05: irq 10, address
00:02:b3:ad:bc:f6
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 0
fxp1 at pci1 dev 5 function 0 "Intel 82557" rev 0x05: irq 5, address
00:02:b3:ad:bc:f7
inphy1 at fxp1 phy 1: i82555 10/100 media interface, rev. 0
clcs0 at pci0 dev 17 function 0 "Cirrus Logic CS4280/46xx CrystalClear
Audio" rev 0x01: irq 5
ac97: codec id 0x43525903 (Cirrus Logic CS4297 rev 3)
ac97: codec features headphone, 18 bit DAC, 18 bit ADC, No 3D Stereo
audio0 at clcs0
wi0 at pci0 dev 18 function 0 "Intersil PRISM2.5" rev 0x01: irq 11
wi0: PRISM2.5 ISL3874A(Mini-PCI), Firmware 1.0.7 (primary), 1.3.6
(station), address 00:09:5b:2f:81:d0
vga1 at pci0 dev 20 function 0 "SIS 5597/5598 VGA" rev 0x68: aperture
at 0xe5000000, size 0x400000
wsdisplay0 at vga1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask f3c5 netmask ffe5 ttymask ffe7
pctr: user-level cycle counter enabled
mtrr: K6-family MTRR support (2 registers)
dkcsum: wd0 matched BIOS disk 80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
wi0: wi_mgmt_xmit: xmit failed
wi0: wi_mgmt_xmit: xmit failed
wi0: wi_mgmt_xmit: xmit failed
wi0: wi_mgmt_xmit: xmit failed
wi0: wi_mgmt_xmit: xmit failed
wi0: wi_mgmt_xmit: xmit failed
wi0: host encrypt not implemented for 802.3
wi0: host encrypt not implemented for 802.3



Here are the other changes I have made:
/etc/hostname.fxp0
inet 66.159.225.84 255.255.255.0 NONE

/etc/hostname.fxp1
inet 172.16.1.253 255.255.255.0 172.16.1.255

/etc/hostname.wi0
up mediaopt hostap
!wicontrol \$if -t 3 -e 1 -f 7 -k passs -n oap

/etc/bridgename.bridge0
add fxp1
add wi0
up

Changes made to /etc/rc.conf:
pf=YES
check_quotas=NO

Changes made to /etc/sysctl.conf:
net.inet.ip.forwarding=1
ddb.panic=0

TIA.
-- 
*-*
Matt Snow
 mattsnow_(_at_)_gmail_(_dot_)_com